Jump to content

  • Announcements

    • NeilT

      Mini Lab Help.com For Sale   03/16/2017

      2017 - Minilab Help could face closure at the end of the year. Our outgoing running cost and time is no longer being covered by our sponsorship. 
      With almost 10,000 members we have grown to be perhaps the worlds largest forum for Mini Lab Help. 
      We would now consider the sale of this web site, please contact us if you wish to discuss. 
Sign in to follow this  
Fotoprimavera

Frontier 350 Error W-2680

Recommended Posts

The error says:

You have reacher the maximum number of prints.

Stop printing.

Anyone have any idea of what i have to do or where i can find support for it?

Thank you.

It only allow me to make ONE print for color adjustment when i'm starting the Minilab.

Share this post


Link to post
Share on other sites

Nash,

there are a few things that can cause this problem.  First off, to get your self back up and running.  Go into setup and maintenance using se2 login and 7777 password.  Goto processor adjustment and maintenance, then processor input/output.  check you replenisher levels, there are 3.  If any are off ballance (2 say yes, 1 says no) then add water to the one that says no.  

     The next step is finding what is causing the problem.  When the replenisher is mixing a new box of chemicals, one of the 3 is not getting enough water.  In the replenisher section, there is a one way valve that tends to wear out and not enough water gets thru, check that and replace if necessary.  Another thing to check is the upper and lower float switches for all 3 replenishers.  sometimes they get dirty and get stuck in the down position, thus fooling the machine the chems are off balance.

     Another thing you might want to do is pull the lower side panel off the side with the main breaker.   Then pull off the panel that surrounds the replenisher section were you load a new box.  breaker off the machine and drain the all replenisher except for the PSR (water).  Turn the machine back on and at some point it should ask for a new box of replenisher.  when it takes it, watch the mix process on the side where the tanks are located.  Watch the float switches and look at the solution level when it stops mixing.  If any are off balance, thats the one you need to investigate for why it's not getting enough water.  

hope this helps.

Eoughphily

Share this post


Link to post
Share on other sites

This error because of  frontier detect difference in replenisher level especially P2RA. you can see in maintenance menu- go to processor Input check- replensiher levels. there must be some level difference. only solution is shutdown the machine thru emrgency OFF. then  drain out  all the chemical from replenisher tank ( not main Tank)  except PSR. pour some hot water thru the cartdige holes to make clean throughly inside the tanks especially P2RA. drain out all and close drain valves. restart machine and put  new cartdiges. let it MIX.

hope this might helps you....

Christina.

Share this post


Link to post
Share on other sites

Hi I got same problem, i use to put some water in and its fixed, but this time maybe i put too much water its leaking out .

on processor I/O the FS742 P2RB uper level showing NO what should i do please help

Share this post


Link to post
Share on other sites

If after mixing of new replenisment cartridge FS742 P2RB uper level still say NO, most probbaly FS742 is fail. After mixing all upper (and lowers) level sensor have to say YES.

You can drain P2RB, check the connector and FS742's  floater.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Sign in to follow this  

×