Jump to content
imagine_vision

laser status fuji 570

Recommended Posts

Hi.  Based on the fact you have the l1 installed it means you are using ms01 software which on my point of view has less quality than the Fe s2. 

To check the laser history. From the menu screen click on setup and maintenance then type password 7777 next open printer maintenance adjustment next scroll down to laser history then click to open then you can check  to know if the values are stable or fluctuating if the second case the laser might be old and must be change soon. 

Share this post


Link to post
Share on other sites

@nanotron
Why did you declare it?
Do you have any official data of comparison MS and FE or you impressed your opinion?
MS01 is newer than FE software, it has more features and more convenient.
And MS and FE have NO attitude to the quality of prints. 
It is just a tool to control the orders and make color adjustments and all depends on the settings of the lab, quality of chemistry and level of skills of the operator.

2. 
As for FF570 purchase.
Better to check ALL lasers.
Not only red is defective there.
yes, it is quite more often to be defective but we also often repair blue lasers also.
So better, make the printscreens of the following menu and place here for consideration:

Fr550/570
0542 B laser data
0543 G laser data
0544 R laser data
0545 Laser exposure check
and error log record

IMPORTANT:
0549 Laser history graph with the next page.
(table with the last data!!!!)
After that, all will be clear.

Share this post


Link to post
Share on other sites
On 8/6/2019 at 9:36, yustas said:

@nanotron
¿Por qué lo declaraste?
¿Tiene algún dato oficial de comparación MS y FE o impresionó su opinión?
MS01 es más nuevo que el software FE, tiene más funciones y es más conveniente.
Y MS y FE NO tienen una actitud hacia la calidad de las impresiones. 
Es solo una herramienta para controlar los pedidos y realizar ajustes de color, y todo depende de la configuración del laboratorio, la calidad de la química y el nivel de habilidades del operador.

2. 
En cuanto a la compra de FF570.
Mejor comprobar TODOS los láseres.
No solo el rojo es defectuoso allí.
Sí, es más frecuente que sea defectuoso, pero también a menudo reparamos láseres azules.
Así que mejor, haga las impresiones del menú siguiente y colóquelas aquí para su consideración:

Fr550 / 570
0542 B datos láser
0543 G datos láser
0544 R datos láser 0545 Control de
exposición de láser
y registro de errores

IMPORTANTE:
0549 Gráfico de la historia del láser con la página siguiente.
(Tabla con los últimos datos !!!!)
Después de eso, todo estará claro.

 

Hello good evening, I attach photos of the laser data to know if you can comment on the status of the same since thank you very much

20190618_170742.jpg

20190618_170755.jpg

Share this post


Link to post
Share on other sites

R laser is good. Red laser diode typical working current is 175 mA, recommended maximal current is 210 mA and maximal pulse current even 350 mA. Now it works at 142 mA and on your software maximum limited to 188.6 mA. This limit can be increased  up to 250 mA, but it is not recommended to set more than recommended maximum current for laser ( 210 mA ) . Anyway I know laser, where current from 150 to 210 increased in 5 month. Look R laser history to see changes there. On other hand laser can be repaired and work again like new. Many times repaired R on 500, 550 and 570.

Share this post


Link to post
Share on other sites

Thank you for your answers I attached other photos with more information


 

https://subefotos.com/ver/?23b8e9cf733a8fddfccd4bbaf78ebcd1o.jpg
https://subefotos.com/ver/?a29b4094d46de995e62b35ac2da74b8co.jpg
https://subefotos.com/ver/?dec6a3f134a53fc48b66b1c371dec636o.jpg
Very grateful for your information, I find it very useful to make the decision to buy the equipment ..
July
Edited by imagine_vision

Share this post


Link to post
Share on other sites

G and B are good also. G works at 289 mA, when maximal on your laser is 392 mA . Fuji software allows to increase it up to 600 mA. B works at 49 mA, when maximal an your laser is 73mA. Fuji software allows to increase it up to 170 mA. On laser history R is idle. G and B during time working current was a little increased, but it is acceptable. Still have big reserve. As I told before on Fuji 500, 550, 570 common fault is broken R laser and in most cases have to repair it.

Share this post


Link to post
Share on other sites

Yes, all lasers are in good condition. Confirm.
Do not despair if you ever meet with a problem of a laser.
We will repair for low price with long warranty period.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...