Software de servicio para dl650

[mait 0]

Tengo una avería en la dl 650 y quería intentar cambiar el cabezal, sabe alguien si existe algún software para quitar la tinta y poder hacer los ajustes luego.

[Minilab service 243]

Įdomu ko čia klausi. Gal pats savęs. Puikiai žinau DL650, bet nesuprantu klausimo. Jei nori atsakymo - rašyk Angliškai.

[mait 0]

1 hour ago, Minilab service said:

Įdomu ko čia klausi. Gal pats savęs. Puikiai žinau DL650, apuesta nesuprantu klausimo. Jei nori atsakymo - rašyk Angliškai.

I have a fault on the dl 650 and wanted to change the head, is there any software to remove the ink and make the adjustments later.

[Minilab service 243]

On DL650 do not need any additional software. All are on maintenance interface and recovery utility ( it is on computer also ) . 

To remove ink you need draining cartridges. To drain ink use menu 0325 ( draining/washing ) . From the same menu can wash print-head ( need cleaning cartridges ) . Sometimes washing is enough to have good prints again. To clean printer also can use Epson print-head maintenance kit and cleaning sheet.

After print-head replacement all can do on recovery utility and maintenance menu. If need to enter password it is 7777.

Are you sure, that really need to replace print head? If the nozzle check pattern is not printed in two lines (for one head), replace the head controller board. If the check pattern is not printed at head 1 or 2 section - replace the head controller board B (DRV).  If the check pattern is not printed at head 3 to 6 section: - replace the head controller board A (DRV) .

DL650 print head has 6 elements and they are the same. Instead to replace print head unit ( with 6 elements ) is possible to change one element ( which doesn't work well ) . Fuji, or Epson doesn't sell them, but it is possible to find head elements online. The same elements used on Epson SL-D3000 and Fuji DL600 ( on DL600 print head - 5 elements ) .

More information can find on Fuji DL650 and Epson SL-D3000 DR manuals ( service manuals , instillation manual , part list ) .

Edited January 21 by Minilab service

[mait 0]

Sorry for taking so long, only half of yellow does not print well on the two heads.  I'm going to try everything he tells me, thank you very much.

[mait 0]

I can't find menu 0325, where is it?

[Minilab service 243]

0325 is not on MS01 maintenance. It is on PRINTER maintenance interface.

[mait 0]

and that menu where it is I can't find it anywhere

[Minilab service 243]

Printer maintenance utility should be on Start, Programs. It is the same interface, where is registered your printer. Select printer and press Maintenance.

There also should be recovery utility. What is your printer system software version? Old versions didn't have recovery utility. To have it need upgrade system software ( for example to version 3.0 ) .

Edited February 3 by Minilab service

[mait 0]

I do see it, but I don't see option 0325.

[hivanov 4]

Press Crtl+Alt+S simultaneously - then enter password 7777 -> setting/maintenance - and you will have extended menu 

 

[mait 0]

I see, thank you very much, I will try to do it, I have here two heads that I bought in aliexpress, I will try to put it.

[hivanov 4]

You can't drain the ink without draining cartridges - normal carriages will not work. try to replace without draining the ink. Just be careful to not spill too much ink around and get good amount of rags/towels/paper

[mait 0]

Won't a lot of ink come out when trying to remove the top of the printhead?

[hivanov 4]

Not if you tap it faster and turn it upside real quick. they are total about 15 ml in the the tubes per colors so not much

[Minilab service 243]

Yes, to see menu 0325 you should be on service mode. As I wrote before password is 7777 ( the same for service mode and recovery utility ) .

Drain cartridge -  Fuji part number PW16G1544988. Cleaning cartridge - Fuji part number PW16G1543865 . The same cartridges are for Fuji DL650 and DL600.

[mait 0]

Hi, I have already changed the 2 heads, but head 4 has a problem and I have to try to clean it so I don't have to change it, can you tell me which one is head 4 in the photo I have doubts.

[Minilab service 243]

All information you can find  on service manual. Look there.

DL650 print head layout is following :
Printhead 1 : Row A - Sky blue, Row B - Pink
Printhead 2 : Row C - Magenta, Row D - Cyan
Printhead 3 : Row E - Yellow, Row F - Black
Printhead 4 : Row G - Black, Row H - Yellow
Printhead 5 : Row I - Cyan, Row J - Magenta
Printhead 6 : Row K - Pink, Row L - Sky blue

Driver boards connected this way :
Board B (DRV)
CN21 - Printhead Row A, FFC: CN21-A
CN22 - Printhead Row B, FFC: CN22-B
CN23 - Printhead Row K, FFC: CN23-K
CN24 - Printhead Row L, FFC: CN24-L

Board A (DRV)
CN21 - Printhead Row I, FFC: CN21-I
CN22 - Printhead Row J, FFC: CN22-J
CN23 - Printhead Row G, FFC: CN23-G
CN24 - Printhead Row H, FFC: CN24-H
CN25 - Printhead Row E, FFC: CN25-E
CN26 - Printhead Row F, FFC: CN26-F
CN27 - Printhead Row C, FFC: CN27-C
CN28 - Printhead Row D, FFC: CN28-D

Here is print head layout

 

Edited Saturday at 04:28 PM by Minilab service

[mait 0]

thank you very much, I'll give it a try