flashed Posted July 8, 2010 Report Share Posted July 8, 2010 Hi experts, hope you will be able to help me with my problem. Tpday I turned on my frontier 330 and the temperature of the Ps1/Ps2 stucken with 35,1 degrees. I temporarely solved the problem with reducing the working temperature of the solution, but like i wrote, it is only temporarely. How can I solve the Problem, without buying a new, rather expensive, circuit board? Thank you very much for your anwsers! Greetz, George Quote Link to comment Share on other sites More sharing options...
tech2 Posted July 9, 2010 Report Share Posted July 9, 2010 George, Are you getting any errors? If so which number error? You say the temperature "gets stuck" on 35.1 does it rise any higher? More information and I may be able to help you Tech2 Quote Link to comment Share on other sites More sharing options...
flashed Posted July 9, 2010 Author Report Share Posted July 9, 2010 Hi Tech2, thank you for the anwser. Yesterday I read the posts about this problem and today i cleaned the heater, changed the filters and the replenischer water, still I have ther same problem. It is like this: Like mentioned, the temperature stucks at 35.1 degrees and it doesn´t fall or get´s higher. You know the prosedure in the morning, where the chemicals in the processor are warmed up. P1, P2, Ps3/4 reach the temperature only Ps1/2 don´t. I get no error message. I also read yesterday, that a SSR has to be replaced, but I have no Idea where this SSr is, or where I can buy it. Hope I gave you enough information, if not, please tell. Thank you very much, George Quote Link to comment Share on other sites More sharing options...
flashed Posted July 9, 2010 Author Report Share Posted July 9, 2010 New Information: I switched the power supply of the heaters Ps1/2 and Ps3/4, also the temperature sensor. Now it is working. Well for now, it is only a temporarely solution, so I need further information of somebody, that knows more than me. Thank you George Quote Link to comment Share on other sites More sharing options...
Kevbo37 Posted July 9, 2010 Report Share Posted July 9, 2010 Does the temperature show 35.1 even when the other temperatures are lower in the morning? If it always shows this temperature then it is a problem with the temperature sensor (thermistor) or the board that interprets this reading into a temperature. Your said you "switched the power supply of the heaters Ps1/2 and Ps3/4, also the temperature sensor", is the same problem now showing on the Ps3/4? Quote Link to comment Share on other sites More sharing options...
flashed Posted July 9, 2010 Author Report Share Posted July 9, 2010 Hi Kevbo 37, sorry I gave not much information as you needed. It is like this. In the morning, when I turn on the frontier, the temperature is the same in each tank, about 22 degrees, today for example, the heater wasn´t heating at all. Just when I turned around the switsches, the heaters started to work. And yes, The PS1/2 is now Ps3/4 and opposite. I will see, what will happen tomorrow, when the mashine was all night long turned off. If it still works. Tommorow you will get a new report... Greetz, George Quote Link to comment Share on other sites More sharing options...
flashed Posted July 12, 2010 Author Report Share Posted July 12, 2010 Ok folks, after I switsched the power supply of the heaters Ps1/2 and Ps3/4 and the temp. sensors, everything is working normal. No idea, why it is like this. But still, this is not a permanent solution, and if anyone of you has an idea, please tell me. Thank you very much, George Quote Link to comment Share on other sites More sharing options...
Kevbo37 Posted July 12, 2010 Report Share Posted July 12, 2010 Maybe you had a bad connection and during the process of switching them it was remedied. Have you tried to switch them back to normal? Quote Link to comment Share on other sites More sharing options...
flashed Posted July 13, 2010 Author Report Share Posted July 13, 2010 Hi Kevbo, yes did this today. Works perfect. Hope this was really a coonnection problem and not something else. But another mistake was shown. E-2663, P1R Pump is not working. When I went to the I/O menu and started the pump, it worked with any problems. A Bug? Greetz, George Quote Link to comment Share on other sites More sharing options...
Kevbo37 Posted July 13, 2010 Report Share Posted July 13, 2010 I am glad to hear it works now. If the pump continues to have this problem, you might try taking it apart carefully and cleaning it. Quote Link to comment Share on other sites More sharing options...
flashed Posted July 14, 2010 Author Report Share Posted July 14, 2010 Ok, I will do that, when it continues. Thank you Kevbo. Greetz, George Quote Link to comment Share on other sites More sharing options...
Sebahattin Posted July 9, 2011 Report Share Posted July 9, 2011 Hello, Our "FUJI FRONTIER 330 SLP 800SC" have printing machine. Frontend server installed on windows 2000. We would like to set up Windows 2000 software uninstall windows xp. A computer with Windows XP installed for the trial, "the MSDE and FDI," I installed the software but the device out of "FUJI FRONTIER 330 SLP 800-SC" printing machine software does not seem to FDI. How can these settings. Thanks in advance for your help E-MAİL: xbaydostx(@)hotmail.com (e-mail at no brackets) ===================================== TURKISH : Merhaba, Bizim "FUJI FRONTIER 330 SLP 800SC" baskı makinası var. Frontend sunucuda windows 2000 yüklü. Biz windows 2000 yazılımı kaldırıp windows xp kurmak istiyoruz. Deneme için Windows Xp kurulu olan bir bilgisayara "MSDE ve FDI" Yazılımı kurduk ancak out device "FUJI FRONTIER 330 SLP 800-SC" baskı makinamız FDI yazılımda görünmüyor. Bu ayarları nasıl yapabiliriz. Yardımlarınız için şimdiden teşekkürler. E-MAİL: xbaydostx(@)hotmail.com ( mail adresinde pazantezler yok ) Quote Link to comment Share on other sites More sharing options...
guesspd Posted June 19, 2012 Report Share Posted June 19, 2012 i had heater problem before and its cause from the relays. after changing relay it work and again came same problem to another heater, but i could not get a replacement relay. so the best solution was to change the processing board which is having bad relays on it. now its works fine as new. Quote Link to comment Share on other sites More sharing options...
KKK Posted July 1, 2012 Report Share Posted July 1, 2012 Try to check heater if no work ,must change SSR (you can find it from electronic shop brand of chip "Amron" or " Mitsubishi" have to show specification to them. In Thailand is not expensive. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.