cyberlab Posted December 30, 2010 Report Share Posted December 30, 2010 please i have this error message w-2411 what can i do? Quote Link to comment Share on other sites More sharing options...
nash Posted December 30, 2010 Report Share Posted December 30, 2010 are you saying "you`ve opened the side doors and can`t find any paper jammed anywhere"? Quote Link to comment Share on other sites More sharing options...
cyberlab Posted December 30, 2010 Author Report Share Posted December 30, 2010 are you saying "you`ve opened the side doors and can`t find any paper jammed anywhere"? Yes, any paper. have you an idea please ? Quote Link to comment Share on other sites More sharing options...
nash Posted December 30, 2010 Report Share Posted December 30, 2010 is the paper magazine loading correctly Quote Link to comment Share on other sites More sharing options...
cyberlab Posted December 30, 2010 Author Report Share Posted December 30, 2010 yes it is Quote Link to comment Share on other sites More sharing options...
nash Posted December 30, 2010 Report Share Posted December 30, 2010 THIS may not be in your case but when i had this problem the engineer replaced the PDC20 PCB and then it was running fine Quote Link to comment Share on other sites More sharing options...
Aaron_RIMG_TSR Posted December 31, 2010 Report Share Posted December 31, 2010 Double check that there is no paper in the printer. If the error still occurs, check the finger sensors up the side doors to make sure that one of them isnt stuck under the metal plate. The sensor at the top turn is typically the one that sticks. Make sure that there is no paper between the printer and processor (it likes to hide there). If all this is fine, the sensors at the processor entrence section could be dirty. They are not easy to get to, but you could look at the manual for the removal of sensors D571, D572, and D573. Hope this helps. Good Luck. Quote Link to comment Share on other sites More sharing options...
audiomax Posted February 25, 2012 Report Share Posted February 25, 2012 How You solve the problem ? I have same error and could not find any paper stuck on printer ....? Quote Link to comment Share on other sites More sharing options...
audiomax Posted February 25, 2012 Report Share Posted February 25, 2012 Problem solved ! One of the six belt at the enter in processor was slide and occured the midle optical sensor at the printer exit ! ....a little bit tricky to put the belt in place ! Quote Link to comment Share on other sites More sharing options...
everQuestion Posted December 30, 2019 Report Share Posted December 30, 2019 I understand that this reply is very late but well... what belt do you mean? There is a roller but the only belt i see is the band where photos pass to move to the processor. I place an upkeep print and started the drive so it could take away the print from the middle. Upkeep print had no trouble passing to the processor section. Where is this belt that you mention? Quote Link to comment Share on other sites More sharing options...
everQuestion Posted December 30, 2019 Report Share Posted December 30, 2019 Quote Link to comment Share on other sites More sharing options...
Miguela Posted June 5, 2020 Report Share Posted June 5, 2020 Hi!! I have the same problem, i´m in Argentina. If someone can help me to find the sensors. You can write in english, y can undestand you. My name is Miguela Quote Link to comment Share on other sites More sharing options...
Minilab service Posted June 5, 2020 Report Share Posted June 5, 2020 Hello Miguela. Which Fuji printer do you have? Here is topic about LP-1500/LP-2000. If you have LP-1500 or LP-2000 and see W-2411 error then go to input check and look paper sensor status ( sensors D541, D552, D560, D561, D562, D571, D572, D573 ) . When paper removed they should be light. Can be closed, dirty, or faulty sensor, bad connection, or faulty CTL20 board. Check what you have on your minilab and then can say more. If you have different printer - write model. Quote Link to comment Share on other sites More sharing options...
Hugor Posted September 24, 2021 Report Share Posted September 24, 2021 Hi, my machine LP 5500 having this error W 2411. Please advice how to use I/O to check the sensor and where is the sensor location. Appreciate your help. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.