Macedonia Posted October 16, 2009 Report Share Posted October 16, 2009 Hello I have a Frontier 375 and I want to work without scanner. I have FMPC software, What configuration computer do I need , which operating system software and what else do I need. Quote Link to comment Share on other sites More sharing options...
sisir Posted October 17, 2009 Report Share Posted October 17, 2009 You should have EEPROM ver 2.0 on CTL20 PCB. Also you should have a PC with 1GB RAM and Two Firewire Port. However, which Version of FMPC do you have? Quote Link to comment Share on other sites More sharing options...
Macedonia Posted October 18, 2009 Author Report Share Posted October 18, 2009 The FMPC software is sent to me from Germany ,still not arrived yet, as soon it arrives I will send the version No. Quote Link to comment Share on other sites More sharing options...
Macedonia Posted October 24, 2009 Author Report Share Posted October 24, 2009 I just received the software : Driver disk Ver.1.0-ox-002 and FMPC Ver.2.1-oe-12 Quote Link to comment Share on other sites More sharing options...
barsheed Posted October 25, 2009 Report Share Posted October 25, 2009 If your machine is new version you not need CTL20 ROM ( small chipset) , check the ROM version for your printer. about the firewire you need just one becuase you not need scanner. Quote Link to comment Share on other sites More sharing options...
Macedonia Posted October 25, 2009 Author Report Share Posted October 25, 2009 The ROM version is 2.0 Quote Link to comment Share on other sites More sharing options...
barsheed Posted October 26, 2009 Report Share Posted October 26, 2009 You not need ROM part. Just startup the machine in rom mode and istall software Quote Link to comment Share on other sites More sharing options...
Macedonia Posted October 28, 2009 Author Report Share Posted October 28, 2009 I have installed the software and the FMPC now controls the LP2000 but when I try to do prints from the FDI the FMPC says that there is no FDI connected ? Quote Link to comment Share on other sites More sharing options...
Macedonia Posted October 29, 2009 Author Report Share Posted October 29, 2009 This is what I get after installing the D20 FMPC software - " insert DI Print/data writing service CD " - can anybody tell me what is the software that it is asking for? Quote Link to comment Share on other sites More sharing options...
sisir Posted October 31, 2009 Report Share Posted October 31, 2009 You should install C4/C5 client on FMPC, then you will be able to Print from DI pc. and the machine is showing you than message Quote Link to comment Share on other sites More sharing options...
Macedonia Posted October 31, 2009 Author Report Share Posted October 31, 2009 I have installed C4/C5 ,when I perss on "PRINT" on the FMPC I get message that there is no conection to the FDI station? Quote Link to comment Share on other sites More sharing options...
sisir Posted November 2, 2009 Report Share Posted November 2, 2009 You should check on service menu, Installation Information Setup > External I/O is it on or off. Quote Link to comment Share on other sites More sharing options...
Macedonia Posted November 3, 2009 Author Report Share Posted November 3, 2009 I get this screen Quote Link to comment Share on other sites More sharing options...
Moniroth Posted November 9, 2009 Report Share Posted November 9, 2009 Make sure you have configure network connection between FMPC and FDi correctly. -FMPC and Fdi are in the same workgroup or not. -FMPC and Fdi can run into each other or not. -Turn off windows firewall on FMPC yet or not. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.