Jump to content

Konica DS2001-E questions and problems


Nekosaka
 Share

Recommended Posts

Hi all !

I just bought a DS2001-E in superb condition for a fair price.

I recovered everything, computer ( XP embedded), scanner, all masks, license key, scanner keyboard, software ... etc.

https://ibb.co/xCfW37F

https://ibb.co/JvK7hV7

https://ibb.co/HTqkk8g

I have a few questions and requests:

1: I can't find my scanned images !?
Where can they go? I tried to look at all possible software folders, there is a d: / storage with the scan information folder in it, but no images ...
it may be necessary to program an external PC?
I tried to change the folder destination, but maybe I did not do the right thing.

https://ibb.co/jhqkLJf

https://ibb.co/JkSPz3z

https://ibb.co/wg5gJTS

2: Is it possible to change the type of image, .Jpg or .Tiff? how?

3: Is it possible to upgrade the firmwire or the software version to the latest as well as for the components?

https://ibb.co/s9S19p2

https://ibb.co/vVCk5vc

4: It seems that the firewire card present in the PC to connect the scanner has a driver problem (there are yellow ? In the hardware components) however everything works correctly but windows tells me that the device does not work correctly, how how to update the driver and how to fix the problem?

5: is it possible to send the scanned images directly to a networked Mac?

6: I have a Konica administrator code on the computer, does anyone know if this code is generic to all Konica computers? i don't have the code and can't do any modification on the computer without the one

 

Thank you in advance for your reply

Edited by Nekosaka
Link to comment
Share on other sites

All that should explain equipment supplier, software supplier, or your service engineer.
1. Path need chance on service setup.
2. File type ( .jpg, bmp, tiff ) , Image resolution ( 1 base, 4 base, 16 base, maximum or real size ) and compressing quality (  basic, normal, fine, superfine ) can select on service setup. If to use "real size" then file size depends on selected print size. Also picture will have the same proportions as print size, so picture if proportions mismatch will be cropped. If chose other options ( 1 base, 4 base, 16 base, maximum )  - will be scanned whole frame. 135 full frame , 4 base - 1024 x 1536 , 16 base - 2048 x 3072 , maximum - 4988 x 7428 . If to use .tiff then file size will be very big. .jpg size depends on compression (  basic, normal, fine, superfine ) . The biggest file size - when selected "Superfine".
Can program 10 scanning services with different settings. On each of them can be different path, file type, resolution, index and other settings.
3. As I see your software on computer is older, than version on scanner, so nothing to upgrade ( can only downgrade ) . Version, which you have now see during startup. You can upgrade computer software to version 2.00R03E ( scanner - version 2.00R2, FPGA - 6.00R0 , zoom - 1.10R1A , AFC - 2.21R0 ) . Also is possible all transfer into new, modern computer running W10 32 bit.
4. Firewire card should show correctly - without yellow symbols. Also should be correctly installed scanner driver. Maybe you have yellow mark on firewire NETWORK driver ( not board driver ) . Firewire network is not used, so no problem, if it is not installed. On other hand firewire network can be installed and have not yellow symbols.
5. Can set path to any disk - real, or virtual. So on Windows can map network drive and set scanning service to store scanned files there.
6. Here standard Konica user and password. Password can be removed, or changed. 
I have all software, manuals, drivers, new options for dongle. Can upgrade this computer, or transfer into other computer ( W7 32 bit, or W10 64 bit ) .

Link to comment
Share on other sites

Thank you Minilab service for your reply.

 

Unfortunately I don't have any equipment supplier, software supplier, or service engineer in France.

I bought the scanner from a store that has stopped operating, and I have no manual...

 

12 hours ago, Minilab service said:

1. Path need chance on service setup.

I tried to find the location on service setup, but nothing...

i will try to double check tonight

 

12 hours ago, Minilab service said:

2. File type ( .jpg, bmp, tiff ) , Image resolution ( 1 base, 4 base, 16 base, maximum or real size ) and compressing quality (  basic, normal, fine, superfine ) can select on service setup. If to use "real size" then file size depends on selected print size. Also picture will have the same proportions as print size, so picture if proportions mismatch will be cropped. If chose other options ( 1 base, 4 base, 16 base, maximum )  - will be scanned whole frame. 135 full frame , 4 base - 1024 x 1536 , 16 base - 2048 x 3072 , maximum - 4988 x 7428 . If to use .tiff then file size will be very big. .jpg size depends on compression (  basic, normal, fine, superfine ) . The biggest file size - when selected "Superfine".

I have not seen this type of setting in the setup service, in which tab is it?

 

12 hours ago, Minilab service said:

3. As I see your software on computer is older, than version on scanner, so nothing to upgrade ( can only downgrade ) . Version, which you have now see during startup. You can upgrade computer software to version 2.00R03E ( scanner - version 2.00R2, FPGA - 6.00R0 , zoom - 1.10R1A , AFC - 2.21R0 ) . Also is possible all transfer into new, modern computer running W10 32 bit.

I work on a Mac, so having a computer with Windows 10 doesn't really interest me.
But I would still like to update the software to the latest version, can you do that online?

 

12 hours ago, Minilab service said:

4. Firewire card should show correctly - without yellow symbols. Also should be correctly installed scanner driver. Maybe you have yellow mark on firewire NETWORK driver ( not board driver ) . Firewire network is not used, so no problem, if it is not installed. On other hand firewire network can be installed and have not yellow symbols.

I tried to reinstall drivers, but I can't because of my administrator password problem.

 

12 hours ago, Minilab service said:

5. Can set path to any disk - real, or virtual. So on Windows can map network drive and set scanning service to store scanned files there.

you say I can set path to any disk, but when I try to configure a new folder or a new EX-PC, the software open a windows with only old networked folder, and I can't add a new one.

 

12 hours ago, Minilab service said:

6. Here standard Konica user and password. Password can be removed, or changed. 
I have all software, manuals, drivers, new options for dongle. Can upgrade this computer, or transfer into other computer ( W7 32 bit, or W10 64 bit ) .

can we talk about it? I would just like to remake a clean pc with a clean windows install before, but it is possible that I call on your services.

Link to comment
Share on other sites

If you bought scanner from store they are suppliers. Questions had to ask them. Ask them to give manuals. If they have not - you can purchase whole set of manuals ( service, user, maintenance, instillation, upgrade manual, part list and others - about 20 .pdf documents ) .

Dis-select scanning service ( print function, EX-PC ) . Then move mouse on this icon. Click right mouse and select service setup.All settings are there. Can program 10 services ( path, resolution, file format... ) . After that can choose service on this icon.

Software doesn't work on MAC. If to use virtual machine then somehow need forward firewire card. Need Windows. Your choice, which to use - Windows 2000, Windows XP, Windows Vista, Windows 7 x86, or W10 x86. 

Administrator password is standard - konicaminolta . It can be changed, or removed.

Can be upgraded system, which you have, or reinstalled everything. The latest version - 2.00R03E. Version see when software is loading. I think you have 1.30, or something like this. On film carrier is loaded 2.21R0 ( the latest ) . Might be before scanner software was upgraded.

All can be upgraded online. When have software and upgrade manual can do it yourself.

Link to comment
Share on other sites

On 19/5/2021 at 15:28, Nekosaka said:

Hola todos !

Acabo de comprar un DS2001-E en excelentes condiciones por un precio justo.

Recuperé todo, computadora (XP incrustado), escáner, todas las máscaras, clave de licencia, teclado del escáner, software ... etc.

https://ibb.co/xCfW37F

https://ibb.co/JvK7hV7

https://ibb.co/HTqkk8g

Tengo algunas preguntas y solicitudes:

1: ¡No puedo encontrar mis imágenes escaneadas!?
¿Adónde pueden ir? Intenté ver todas las carpetas de software posibles, hay un anuncio: / almacenamiento con la carpeta de información de escaneo, pero no hay imágenes ... ¿
puede ser necesario programar una PC externa?
Intenté cambiar el destino de la carpeta, pero tal vez no hice lo correcto.

https://ibb.co/jhqkLJf

https://ibb.co/JkSPz3z

https://ibb.co/wg5gJTS

2: ¿Es posible cambiar el tipo de imagen, .Jpg o .Tiff? ¿Cómo?

3: ¿Es posible actualizar el firmware o la versión del software a la última versión, así como para los componentes?

https://ibb.co/s9S19p2

https://ibb.co/vVCk5vc

4: Parece que la tarjeta firewire presente en la PC para conectar el escáner tiene un problema de controlador (¿hay amarillo? En los componentes de hardware) sin embargo todo funciona correctamente pero Windows me dice que el dispositivo no funciona correctamente, cómo actualizar el controlador y cómo solucionar el problema?

5: ¿es posible enviar las imágenes escaneadas directamente a una Mac en red?

6: Tengo un código de administrador de Konica en la computadora, ¿alguien sabe si este código es genérico para todas las computadoras Konica? No tengo el código y no puedo hacer ninguna modificación en la computadora sin el

 

Gracias de antemano por su respuesta

Hello! I was looking for scan samples from the DS scanner and came across this, 
I would like to ask you if the quality is optimal and if it is worth the investment. Could you send me scan samples?
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...