problems with image processing 3001

[arche hernandez sanchez]

The image processing has already been changed and it was tested with 2 other cards and it does the same, it marks an error

[arche hernandez sanchez]

hace 12 minutos, arche hernandez sanchez dijo:

The image processing has already been changed and it was tested with 2 other cards and it does the same, it marks an error

 

[Dave S]

What is the status of the LED’s 1-8 on the image processing PCB?

[arche hernandez sanchez]

Hace 34 minutos, Dave S dijo:

¿Cuál es el estado del LED 1-8 en la PCB de procesamiento de imágenes?

I do not know

[PHOTOLABPART.COM]

RESPECTED SIR 

PLEASE LOOK IN PICTURE HOW MANY LED IS ON WHEN YOU START MACHINE ?

[arche hernandez sanchez]

El 9/12/2021 a las 12:49 PM, PHOTOLABPART.COM dijo:

RESPETADO SEÑOR

POR FAVOR, MIRE EN LA IMAGEN ¿CUÁNTOS LED HAY ENCENDIDOS CUANDO ENCIENDE LA MÁQUINA?

the 8 leds do turn on

[PHOTOLABPART.COM]

RESPECTED SIR 

PLEASE CHECK ALL CONNECTION IF ALL IS OKAY CHANGE RAM MAY BE RAM PROBLEM FOR THIS ERROR 

 

THANK YOU 

[arche hernandez sanchez]

Hace 1 hora, PHOTOLABPART.COM dijo:

RESPETADO SEÑOR

COMPRUEBE TODA LA CONEXIÓN SI TODO ESTÁ BIEN CAMBIAR RAM PUEDE SER UN PROBLEMA DE RAM PARA ESTE ERROR

 

GRACIAS

I can put ram pc133 of 512 mb

[PHOTOLABPART.COM]

YES  SIR 

[Dave S]

Noritsu never used more than 256MB of PC133 RAM per slot on the image processing PCB, I personally would not go above 256MB

[Minilab service]

Board works with 512 MB RAM, but no reason to use it. As written above Noritsu used only 128 MB and 256 MB.

[Tengi2]

I onced experience with this error when doing daily setup, the setup failed and the paper come out almost blank except last two lines. I swapped two ram between the pc and the image pcb, the error was cleared but unfortunately images failed to open when printing as the ram from image pcb were too small, I then replaced one ram from PC with another 256mb ram from my spare bank and the problem was solved

 

[Dave S]

Standard machines have x3 128MB sticks of RAM installed on the image processing PCB. If the machine has the optional 120 film carrier then 2 of the RAM sticks were replaced with 256MB sticks.

The PC came with x2 256MB RAM sticks as standard.

The image processing PCB is very fussy with RAM not all PC133 RAM will operate normally with it.

[arche hernandez sanchez]

18 hours ago, Dave S said:

Noritsu nunca usó más de 256MB de RAM PC133 por ranura en la PCB de procesamiento de imágenes, yo personalmente no iría más allá de 256MB

ok

[arche hernandez sanchez]

but if I can use it for a little more speed

[arche hernandez sanchez]

17 hours ago, Minilab service said:

La placa funciona con 512 MB de RAM, pero no hay razón para usarla. Como se escribió anteriormente, Noritsu usó solo 128 MB y 256 MB.

but if I can use it for a little more speed

[arche hernandez sanchez]

9 hours ago, Tengi2 said:

Una vez experimenté con este error al hacer la configuración diaria, la configuración falló y el papel salió casi en blanco, excepto las últimas dos líneas. Intercambié dos ram entre la PC y la PCB de imagen, el error se borró, pero desafortunadamente las imágenes no se abrieron al imprimir ya que la ram de la PCB de imagen era demasiado pequeña, luego reemplacé una RAM de la PC con otra RAM de 256 MB de mi banco de repuesto y el problema se resolvió

 

because I have 1 3202 pro and it had 128 mb pc133 ram and the csmbie for 512mb and if I grab it

[arche hernandez sanchez]

6 hours ago, Dave S said:

Las máquinas estándar tienen x3 sticks de RAM de 128 MB instalados en la PCB de procesamiento de imágenes. Si la máquina tiene el soporte de película 120 opcional, entonces 2 de los sticks de RAM fueron reemplazados por sticks de 256MB.

La PC venía con x2 256MB RAM sticks de serie.

La PCB de procesamiento de imágenes es muy exigente con la RAM, no toda la RAM PC133 funcionará normalmente con ella.

I'm going to put the 512 to see what happens

[Dave S]

1 hour ago, arche hernandez sanchez said:

but if I can use it for a little more speed

Adding more RAM to the image processing PCB will not increase the speed.

1 hour ago, arche hernandez sanchez said:

because I have 1 3202 pro and it had 128 mb pc133 ram and the csmbie for 512mb and if I grab it

You are wrong, the 3202 Pro does not use PC133 RAM anywhere.

 

1 hour ago, arche hernandez sanchez said:

I'm going to put the 512 to see what happens

Do as you wish, there is zero benefit using RAM sticks greater than 256MB on the 3001 image processing PCB.

Edited September 17, 2021 by Dave S

[arche hernandez sanchez]

15 hours ago, Dave S said:

Adding more RAM to the image processing PCB will not increase the speed.

You are wrong, the 3202 Pro does not use PC133 RAM anywhere.

 

Do as you wish, there is zero benefit using RAM sticks greater than 256MB on the 3001 image processing PCB.

Or will it be because you have never opened the compartment where it goes, this is the one I brought was 256mb and I put the 512 one and you see the difference is faster to process the photos

[Dave S]

1 hour ago, arche hernandez sanchez said:

Or will it be because you have never opened the compartment where it goes, this is the one I brought was 256mb and I put the 512 one and you see the difference is faster to process the photos

 

There is no removable PC133 RAM on the 32 series image processing PCB.

The board that has the removable RAM is the image correction PCB, and yes you are correct it does use PC133 SO-DIMM, I thought this was DDR RAM I was wrong.

However increasing the RAM size will not make any difference to the processing speed of the photos, to increase the image processing speed you would need a faster CPU on the image processing PCB and on the image correction PCB.
The printer prints at a fixed speed largely determined by the speed of the paper processor, so no amount of increasing the data processing time is going to make any difference to the actual printing speed.

A faster PC though will make a big difference to the speed the images arrive on the screen, and will increase certain image processing tasks, but again it will have no influence on how quickly the printer actually makes the prints.

[arche hernandez sanchez]

4 hours ago, Dave S said:

There is no removable PC133 RAM on the 32 series image processing PCB.

The board that has the removable RAM is the image correction PCB, and yes you are correct it does use PC133 SO-DIMM, I thought this was DDR RAM I was wrong.

However increasing the RAM size will not make any difference to the processing speed of the photos, to increase the image processing speed you would need a faster CPU on the image processing PCB and on the image correction PCB.
The printer prints at a fixed speed largely determined by the speed of the paper processor, so no amount of increasing the data processing time is going to make any difference to the actual printing speed.

A faster PC though will make a big difference to the speed the images arrive on the screen, and will increase certain image processing tasks, but again it will have no influence on how quickly the printer actually makes the prints.

in the 3202 pro the motherboard I have updated

[arche hernandez sanchez]

4 hours ago, Dave S said:

There is no removable PC133 RAM on the 32 series image processing PCB.

The board that has the removable RAM is the image correction PCB, and yes you are correct it does use PC133 SO-DIMM, I thought this was DDR RAM I was wrong.

However increasing the RAM size will not make any difference to the processing speed of the photos, to increase the image processing speed you would need a faster CPU on the image processing PCB and on the image correction PCB.
The printer prints at a fixed speed largely determined by the speed of the paper processor, so no amount of increasing the data processing time is going to make any difference to the actual printing speed.

A faster PC though will make a big difference to the speed the images arrive on the screen, and will increase certain image processing tasks, but again it will have no influence on how quickly the printer actually makes the prints.

wing 3202 pro I put solid disk 120, ddr2 4gb

[arche hernandez sanchez]

5 hours ago, arche hernandez sanchez said:

Or will it be because you have never opened the compartment where it goes, this is the one I brought was 256mb and I put the 512 one and you see the difference is faster to process the photos

with the 3001 put more memory pc133 512mb to the image processor, and update the motherboard of the computer

[Dave S]

5 hours ago, arche hernandez sanchez said:

with the 3001 put more memory pc133 512mb to the image processor, and update the motherboard of the computer

Like I said upgrading the PC will increase the speed the images get onto the screen etc, but increasing the RAM on the image processing PCB will not make any difference.