film scan Posted October 9, 2021 Report Share Posted October 9, 2021 (edited) 35mm에서만 이렇게 나옵니다. 그것은 특별한 긍정적 인 부분에서 분명히 나옵니다. 우리 기술자들도 그 이유를 모른다고 합니다. 아시는 분 계시면 도와주시겠습니까? Not shown on s-2 or sp-3000. Edited October 10, 2021 by film scan Quote Link to comment Share on other sites More sharing options...
TECNOR Posted October 10, 2021 Report Share Posted October 10, 2021 Write in english please film scan 1 Quote Link to comment Share on other sites More sharing options...
film scan Posted October 11, 2021 Author Report Share Posted October 11, 2021 On 2021. 10. 10. at 오전 8시 52분, film scan said: This is a 35mm scan of the HS-1800. 120 doesn't work. Only 35mm has such a grid shape? We contacted our engineer, but they say they don't know. If anyone knows, please advise. thank you. Have a nice day. On 2021. 10. 10. at 오전 9시 56분, TECNOR said: 영어로 써주세요 s-2 또는 sp-3000에는 표시되지 않습니다. Quote Link to comment Share on other sites More sharing options...
davidlam Posted October 12, 2021 Report Share Posted October 12, 2021 try remove the [ Lens unit ] underneath the AFC-II used to scan 135 ... to see ... any different ? film scan 1 Quote Link to comment Share on other sites More sharing options...
film scan Posted October 12, 2021 Author Report Share Posted October 12, 2021 4 hours ago, davidlam said: 135를 스캔하는 데 사용된 AFC-II 아래에 있는 [렌즈 장치]를 제거해 보십시오... 다른 점이 있습니까? Thank you for answer. Even removing it causes the same problem. Quote Link to comment Share on other sites More sharing options...
Minilab service Posted October 12, 2021 Report Share Posted October 12, 2021 Is it 135AFC-II, or 135/240AFC-II? If second - try to scan APS film and look there. It is banding. Film advance is unstable. It is some mechanical fault - bad rollers, broken gear, bearing, belt, or something else. Need to repair film carrier. film scan 1 Quote Link to comment Share on other sites More sharing options...
film scan Posted October 15, 2021 Author Report Share Posted October 15, 2021 On 2021. 10. 12. at 오후 4시 54분, Minilab service said: 135AFC-II입니까, 135/240AFC-II입니까? 두 번째 경우 - APS 필름을 스캔하고 살펴보십시오. 밴딩입니다. 필름 진행이 불안정합니다. 롤러 불량, 기어 파손, 베어링, 벨트 등의 기계적 결함입니다. 필름 캐리어를 수리해야 합니다. Thank you for answer. The same thing happens when working with a different carrier. Even after focus correction, the picture is blurry, and I am frustrated because I do not know the cause. Quote Link to comment Share on other sites More sharing options...
Minilab service Posted October 15, 2021 Report Share Posted October 15, 2021 What is the problem on your scanner? I thought you asked about vertical lines. In most cases them caused unstable film advance in film carrier. Did you make focus using charts ( original, metal charts from Noritsu ) . You did focus on all zoom rates ( to change press F, change a zoom ) ? film scan 1 Quote Link to comment Share on other sites More sharing options...
film scan Posted October 16, 2021 Author Report Share Posted October 16, 2021 On 2021. 10. 15. at 오후 4시 31분, Minilab service said: 스캐너에 어떤 문제가 있습니까? 수직선에 대해 질문하신 것 같습니다. 대부분의 경우 필름 캐리어에서 불안정한 필름 진행이 발생했습니다. 차트(Noritsu의 원본, 금속 차트)를 사용하여 초점을 맞추셨습니까? 모든 확대/축소 비율에 초점을 맞추셨습니까(변경하려면 F를 누르고 확대/축소를 변경)? Yes, I used the method you suggested. I also used this carrier on another computer with a new carrier and the scanner had no problems. And the grain in the photo is worse than the previous result. Sorry for the troublesome inquiries. Please understand the frustration. Quote Link to comment Share on other sites More sharing options...
Dave S Posted October 16, 2021 Report Share Posted October 16, 2021 Are you using EZcontroller (with dongle) or the Twain driver software (without dongle)? film scan 1 Quote Link to comment Share on other sites More sharing options...
film scan Posted October 17, 2021 Author Report Share Posted October 17, 2021 13 hours ago, Dave S said: EZcontroller(동글 포함) 또는 Twain 드라이버 소프트웨어(동글 제외)를 사용하고 있습니까? Hello. Thank you for answer. Yes, I am using an EZ controller and a dongle. Quote Link to comment Share on other sites More sharing options...
Dave S Posted October 17, 2021 Report Share Posted October 17, 2021 13 minutes ago, film scan said: Hello. Thank you for answer. Yes, I am using an EZ controller and a dongle. Ok, Try setting the Graininess suppression to 0 and the Sharpness setting to -3 in DSA. film scan 1 Quote Link to comment Share on other sites More sharing options...
film scan Posted October 20, 2021 Author Report Share Posted October 20, 2021 On 2021. 10. 17. at 오후 7시 34분, Dave S said: 좋습니다 . DSA에서 거칠기 억제를 0으로, 선명도 설정을 -3으로 설정해 보십시오. thank you. thank you. The teacher is my god. Strange colors appear when scanning old film on hs-1800. Can you tell me why? Sorry for asking for too much. Quote Link to comment Share on other sites More sharing options...
Dave S Posted October 20, 2021 Report Share Posted October 20, 2021 8 hours ago, film scan said: Strange colors appear when scanning old film on hs-1800. Can you tell me why? Sorry for asking for too much. It is normal, old film often deteriorates and you end up with cross curve colours. There is a Noritsu option software called Tone curve correction, this will allow you to adjust the curves of each colour, there is also an auto correction button that can often really help. film scan 1 Quote Link to comment Share on other sites More sharing options...
film scan Posted October 21, 2021 Author Report Share Posted October 21, 2021 16 hours ago, Dave S said: It is normal, old film often deteriorates and you end up with cross curve colours. There is a Noritsu option software called Tone curve correction, this will allow you to adjust the curves of each colour, there is also an auto correction button that can often really help. thank you. thank you.thank you. thank you. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.