Jump to content

Change motherboart Noritsu 3300 soft v7.02


imagine_vision
 Share

Recommended Posts

On 2/22/2022 at 11:33 AM, imagine_vision said:

 

hello, good afternoon, I wanted to check if the software version 7.02 can be installed in w xp.... and if it is feasible to also change the motherboard for an updated one, so that the system works faster, if someone can give me some information I would appreciate it... .july

H310M S2P (Rev. 1.0) | Placas Base - GIGABYTE

Link to comment
Share on other sites

El 2/22/2022 a las 11:33 AM, imagine_vision dijo:

 

hola, buenas tardes, quería comprobar si la versión de software 7.02 se puede instalar en w xp.... y si es factible cambiar también la placa base por una actualizada, para que el sistema funcione más rápido, si alguien me puede dar alguna información se lo agradecería... . Julio

GA-F2A68HM-DS2H (rev. 1.1) Descripción | Tarjetas Madre - GIGABYTE México

 

Link to comment
Share on other sites

58 minutes ago, virgilio 7u7 said:

For a QSS-3300 this motherboard will not work, as it only has 1 PCI slot.
You need a motherboard with 2 PCI slots for this machine.

 

1 hour ago, virgilio 7u7 said:

This motherboard appears to only have Windows 10/11 64 bit support, so cannot be used with 32 bit Windows XP

 

A G31 or G41 based motherboard with at least 2 PCI slots is required.

Edited by Dave S
Link to comment
Share on other sites

hace 7 minutos, adamwooo dijo:

Algunas compañías hacen la actualización principal i5, i7 de Noritsu 3300. En mi minilab tengo ranura 775, y procesador core2duo e8400. ¿Tienes alguna idea, qué placa base se ejecutará bajo Windows 2000 con procesador i5, i7?

if it works if you put the processor
Link to comment
Share on other sites

18 hours ago, adamwooo said:

Some companies make the core i5, i7 upgrade of Noritsu 3300. In my minilab i have 775 slot , and core2duo e8400 processor. Have You got any idea ,which motherboard will run under windows 2000 with i5, i7 processor?

Asrock Z77 Mtherboards support i5 and i7 and has Windows XP support.
I don’t know if it is compatible with the Noritsu PCI cards as I haven’t tested it myself.

If you are willing to put in the work and do the reading there is information here about installing Windows XP on modern hardware.
https://www.tenforums.com/general-support/172922-windows-xp-2021-system-build-modern-pc.html

Let us know how you get on!!

Link to comment
Share on other sites

I have ordered today some spare parts with intel core i5. Now i am printing on core 2 duo E8400 which i changed myself. I remember then i was changing the processor to E8400, i have tried to change to i3. I had a big problem with windows 2000, computer have been restarted all time and blue screen. Now i know where was the misteake. The problem caused usb 3.0 port. So now i will try with motherboard with usb 2.0. I will let You know when i finish upgrade.

Link to comment
Share on other sites

hace 56 minutos, adamwooo dijo:

He pedido hoy algunas piezas de repuesto con intel core i5. Ahora estoy imprimiendo en core 2 duo E8400 que cambié yo mismo. Recuerdo que entonces estaba cambiando el procesador a E8400, he intentado cambiar a i3. Tuve un gran problema con Windows 2000, la computadora se ha reiniciado todo el tiempo y la pantalla azul. Ahora sé dónde estaba el error. El problema causó el puerto usb 3.0. Así que ahora lo intentaré con la placa base con usb 2.0. Te lo haré saber cuando termine de actualizar.

with i3 or i5 processors the computer is going to restart since it is a lot of power that is why it restarts
Link to comment
Share on other sites

On BIOS settings for HD need choose IDE mode. If there selected AHCI then on standard Windows 2000 have blue screen. Other possibility is to install AHCI driver, but it is not so easy on Windows 2000, or Windows XP.

Yes, i5, i7 use more power. On minilab can be used standard power supply ( without UPS ) . Just need to disable auto shutdown ( connect pin to +5V ) .

There are many i5, i7 models and they used on different platforms. It is possible to find one, which can be used on minilab. Just motherboard should have real COM port ( can be internal, or external ) and one PCI slot ( or more ) .

If you want to use Noritsu network ( connect EZ controller, QSS Kids, printdriver, or something else ) then on computer should be Windows 2000. On XP all that will not work. On modern computers can be installed modded Windows 2000 ( Blackwingcat, or some other ) . Windows 2000 is more stable and reliable, than Windows XP. 

Link to comment
Share on other sites

I have finished to upgrade my computer in Noritsu 3300.  Computer has i5 2500K processor, is working on standard power supply. Have a little problems with drivers, so i can't use graphic card and ethernet card on motherboard, have bought used one.  Now Windows 2000 shows 4 core CPU and 10 gb of memmory, to do this i used Kernelex and PAE mode. SO now should be really fast minilab.

win2k.jpg

Link to comment
Share on other sites

On 2/27/2022 at 11:49 PM, Minilab service said:

Yes, i5, i7 use more power. On minilab can be used standard power supply ( without UPS ) . Just need to disable auto shutdown ( connect pin to +5V ) . 

 

Where can i find this cable ? Is it one of the power supply cable ? Should i disable it , during everything is working ?

Edited by adamwooo
Link to comment
Share on other sites

3 hours ago, adamwooo said:

He terminado de actualizar mi computadora en Noritsu 3300. La computadora tiene procesador i5 2500K, está trabajando en la fuente de alimentación estándar. Tengo un poco de problemas con los controladores, por lo que no puedo usar la tarjeta gráfica y la tarjeta Ethernet en la placa base, he comprado uno usado. Ahora Windows 2000 muestra 4 núcleos de CPU y 10 gb de memmory, para hacer esto utilicé kernelex y modo PAE. Así que ahora debería ser un minilaboratorio realmente rápido.

win2k.jpg

the quality did not change
Link to comment
Share on other sites

  • 3 weeks later...
On 7/3/2022 at 22:53, adamwooo said:

La calidad es bastante buena. 

Would you be so kind as to indicate which motherboard you used and more details for the coding, I am not a computer expert.... I also suppose that it increased the speed in loading files... thank you very much

 

Link to comment
Share on other sites

On 29/3/2022 at 18:35, Minilab service said:

Si realmente desea aumentar la velocidad de carga de archivos, conecte una computadora externa nueva y moderna con W10 de 64 bits. Allí instale el controlador EZ (6.60 y la última versión 7.41). Todos los archivos digitales se pueden imprimir desde esta computadora.

Thank you for your quick response....if I have evaluated that possibility, the problem would be much more expensive since I do not have the necessary software to implement that modification, that is why my query....
Link to comment
Share on other sites

On 3/29/2022 at 5:35 PM, Minilab service said:

If you really want to increase file loading speed then connect new, modern external computer with W10 64 bit. There install EZ controller ( 6.60 and latter the latest -  version 7.41 ) . All digital files you can print from this computer.

We also have a QSS-3300 printer, and a new modern external computer. Can you explain how to do this? We have EZ controller 6.80. How can I update to version 7.41? Are there any other programs we need? I think we also need the 3300 software...

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...