Paper has jammed in the Paper Supply Unit No.06208 -00001

[Reynaldo]

Hola, buen día. Espero que todos estén bien. De nuevo, me encuentro con problemas muy extraños. Aquí les dejo un breve resumen de la situación:

No había apagado mi equipo Noritsu en más de 10 años. De repente, decidí apagarlo por la noche con el interruptor y encenderlo por la mañana. Después de eso, empecé a experimentar un problema con la fuente de alimentación y otras anomalías extrañas.

El problema que tengo ahora es que la máquina funcionaba con normalidad cuando apareció el código de error 06208-00001. Visualmente, el motor de la PM9 no gira. En modo manual, parece funcionar, pero también se bloquea y deja de girar. Como solución rápida, cambié el motor, pero el problema persiste.

Reemplacé toda la Unidad de Exposición Avanzada y la instalé en otra máquina, y el motor funciona correctamente. No es una falla del motor, así que no puedo explicar qué sucede. Lo único que se me ocurre es un problema con el voltaje de ese motor.

Si tienes alguna hipótesis, te la agradecería. Saludos.

 

 

Edited March 8 by Reynaldo

[Dave S]

I only understand posts written in English.
Also I don't know what machine you are talking about.

[Balázsovics]

9 hours ago, Dave S said:

I only understand posts written in English.
Also I don't know what machine you are talking about.

I'm guessing 32 series Noritsu??!
I have no idea what's this guy is on about

[Reynaldo]

Hello, I apologize for my language.

Machine: Noritsu 3704

 

Hello, good day. I hope everyone is well. Once again, I'm encountering some very strange problems. Here's a brief summary of the situation:

I hadn't turned off my Noritsu camera in over 10 years. Suddenly, I decided to turn it off at night with the switch and turn it on in the morning. After that, it started experiencing a problem with the power supply and other strange anomalies.

The problem I'm having now is that the camera was working normally when error code 06208-00001 appeared. Visually, the PM9 motor isn't rotating. In manual mode, it seems to work, but it also jams and stops rotating. As a quick fix, I replaced the motor, but the problem persists.

I replaced the entire Advanced Exposure Unit and installed it in another camera, and the motor works correctly. It's not a motor failure, so I can't explain what's happening. The only thing I can think of is a problem with the voltage of that motor.

If you have any hypotheses, I would appreciate them. Regards.

[Reynaldo]

In summary, the Exposure Advance motor 1 in the process isn't turning; it seems to be stuck or jammed. In manual mode, it sometimes turns but also gets stuck. I replaced the motor, and the problem persists.

Regards.

[Dave S]

Check the connector plugs on the Exposure Advance Unit and on the Printer I/O PCB 1 (J391483) are properly connected.

Do all the other PM motors run properly?

If it is not rotating properly in output check, it's possible the PM driver is bad. It is part of the Printer I/O PCB 1 (J391483) which is located under the paper loading unit inside the black box.
The other cause is poor connections from the Printer Control PCB (J391423) on plug J/P200 not telling the motor to always move. It is located to the right of Magazine B.

[Reynaldo]

Hi, thank you very much. I've already found the problem; it was a circuit board that damaged two motors. My question is, which circuit board or power supply could damage that motor? Regards.

[Dave S]

1 hour ago, Reynaldo said:

Hi, thank you very much. I've already found the problem; it was a circuit board that damaged two motors. My question is, which circuit board or power supply could damage that motor? Regards.

The Printer I/O PCB 1 (J391483) controls this motor.

[Reynaldo]

On 11/3/2026 at 14:07, Dave S said:

La placa de circuito impreso de E/S de la impresora 1 (J391483) controla este motor.

Thank you very much, Dave. Regards.