servitel Posted October 29 Report Posted October 29 I want to install MS01 version 4.0 on the computer connected to the Frontier LP-5700, in such a way that I can also send jobs directly from that same machine. In other words, I want both the FMPC and DICIII to run on the same computer, allowing me to eliminate the need for a separate PC. I tested this by installing Windows 7 on that machine and then installing the 1394 interface card along with its Windows 7 driver. During the MS01 installation, I selected "tethered printer"; however, the installer prompted for a scanner. Although I no longer have a scanner, I selected the SP-3000, and the installation completed without any issues. Yet, when I launch the software, I cannot find the menu for maintenance or for registering the paper magazines. What might I be doing wrong? Thanks.
Minilab service Posted October 29 Report Posted October 29 If to use MS01 software then need two computers - FMPC and server. Of cource it is possible to install server on virtual computer. MS01 version 4.0 is for Windows 7 x86 ( 32 bit ) . Newer MS01 versions are 4.2 ( for W7 x86 ) and 10.0 ( for W10 x64 ) . On one computer can install MS01 4.2 R ( on W7 x86 ) , or W10 10.0 R ( on W10 x64 ) , Then do not need second computer ( real, or virtual ) . I can help to install on one computer. Write private message if need a help to do it.
Pokey Posted October 29 Report Posted October 29 Do not chose tethered. With this choice all the menus are on the SP 3000 as the scanner controls all LP function.
servitel Posted October 29 Author Report Posted October 29 That’s what I thought; in fact, I went into the settings and noticed that the SP 3000 appeared as the output. It reminded me of the FDIA when we connected it that way. Thanks, Pokey—I appreciate the response; it’s a big help.
servitel Posted October 29 Author Report Posted October 29 Thank you, Minilab Service, for the response; you are always attentive to our questions. I understand that the new versions—MS01 4.2 R and 10.0 R—can be installed on a single computer, but I would like to know if any firmware update is also required for the Frontier LP5700; we currently have version 2.0.
Minilab service Posted October 29 Report Posted October 29 Firmware upgrade is not necessary, but it is recomended. Firmware upgrades are on MS01 CDs. On MS01 CDs are firmware versions 3.0-0X-001 , or 3.0-0X-002. Version 3.0-0X-101 is on CD with L1 software ( long length print software - to print 640 mm length ) . "R" versions are not new. They are special versions to connect LP5700 ( 5500, 5900 ) to one computer. To connect LP5700 can use any MS01 version : MS01 4.2 : two computers ( server can be virtual ) , both W7 x86 MS01 4.2R : one computer, W7 x86 MS01 10.0 : two computers ( server can be virtual ) , both W10 x64 MS01 10.0R : one computer, W10 x64 Tethered option can be used when printer is connected through scanner ( server - scanner - printer ) . Can't use it when you have FMPC . servitel 1
servitel Posted October 30 Author Report Posted October 30 I have installed both units. The DICIII was set up with Windows 7 x86 without any issues. For the FMPC, I tried two different approaches using different disks; the first used Windows 7 x86 (configured as a printer), but when I began creating the magazines, an "Epx" error occurred and the system froze. When I used Windows XP, there were no such issues; however, while I am able to create the magazines, attempting to print a calibration strip triggers the following message: "W-2314 Updating backup memory in printer failed. Check parameter file." I am not sure which file this refers to.
Minilab service Posted October 31 Report Posted October 31 (edited) MS01 configuration is correct - server computer and printer computer. Instillation on W7 x86 and W10 x86 is more complicated than it is on Windows XP. Need have expierence to install them. MS01 4.0 is for older version for Windows 7 x86 . On FMPC need make many Windows settings. For Windows XP version 3.1 and older ( 3.0, 2.5.5 , 2.1 ) . Not sure if version 4.0 on XP can work correctly. W-2314 means file acquisition has failed while connecting to the FMPC. Can be insufficient number of printer/processor parameter files are stored in the FMPC. During instillation you had to load them from disk "A". By default it is floppy, but it is possible to use something else ( for example virtual disk ) . Other posibility installation has been performed incompletely, or software doesn't work properely. Then need reinstall software. Need prepare computer correctly ( correct Windows version, make Windows settings, install drivers ) , correctly install FMPC and during insillation load printer/processor settings. Edited October 31 by Minilab service
servitel Posted November 1 Author Report Posted November 1 Good evening, thank you for your response. This is the same installation process I’ve been using for over a year; however, I’ve never encountered this warning message before, which is now preventing me from calibrating the paper. When installing it on the FMPC, it requests "diskette A"—since those are no longer available, I use a Virtual Floppy Drive (VFD) to perform the installation, and it hasn’t caused any issues until now.
Minilab service Posted November 1 Report Posted November 1 You have agree to read backup from floppy. Floppy can be virtual, but it should be letter "A" . There should be loaded correct backup files. W-2314 means problem with data ( wrong, or missing ) , or here problem with FMPC software.
servitel Posted November 2 Author Report Posted November 2 Yes, that is what I have been doing for a year; the backup disk is set up as drive A: in the virtual floppy drive. The problem is that it now won't let me calibrate the paper, and I’m not sure why—I hadn’t encountered any issues previously. It’s possible there’s a fault in the FMPC.Buenas noches, gracias por tu respuesta. Este es el mismo proceso de instalación que he estado usando durante más de un año; sin embargo, nunca antes me había encontrado con este mensaje de advertencia, que ahora me impide calibrar el papel. Al instalarlo en el FMPC, solicita "disquete A" —dado que ya no están disponibles, uso una unidad de disquete virtual (VFD) para realizar la instalación y no ha causado ningún problema hasta ahora.
Minilab service Posted November 2 Report Posted November 2 If you sure, that backup was loaded correctly, files were good, but have W-2314 error then it can be caused by FMPC software.Try reinstall it from beginning : Windows , computer settings, drivers, connection to server and printer, driver settings, network settings, W7 hotfix, MS01, backup.
servitel Posted November 2 Author Report Posted November 2 Thanks, I’m going to reinstall it. I also managed to get a new 1394 card that I’ll test out; the previous one might be faulty, as it’s been in use for a long time. I’ll let you know the results.
Minilab service Posted November 2 Report Posted November 2 Not all firewire boards can be used. On FMPC the best to use Ricoh firewire cards - FW3 with TI chip, or FW4 with NEC. Inside printer image box and scanner image box used FW4, so with LP5700 this card is recommended. It is possible to use some other firewire boards with exact NEC chip ( the same as it is on FW4 ) , but not all they work stable.
servitel Posted Thursday at 04:00 PM Author Report Posted Thursday at 04:00 PM The 1394 card is a Ratoc FW4 that I managed to find brand new. I installed it, and it works very well; it’s clear that if I need any cards other than Ratoc, I should look for ones with an NEC chip—thanks for that tip. I’ve reinstalled the FMPC and DICIII; they connect properly, and the MS01 communicates perfectly, but it won’t let me calibrate the paper. Paper magazines are created without any issues; I even tried sending a 6x8 print job—it went through, but it didn’t print because it triggered the same "Backup Memory" error. Using the 5700’s control pad, I sent a 6-inch calibration sheet, which printed without any problems; I then ran it through the calibration process, and it completed successfully.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now