Tomas

Wash thoroughly the rollers of crossover rack no. 2.

Thank you Minilab Service. You are real Genius and very helpful. Happy New Year.!!!

Thank you for the information. Aside from LDD23, is there any chance that the CTL23 is defective?

Do anyone knows the meaning of this error from Fuji570, E-2821 CTL23? Any information are highly appreciated.

If there are no errors, just perform daily setup and exposure position adjustment from service menu. 

Load the backup. It is software problem. 

Laser exposure position adjustment is required. 

If solenoids works on output check mode means 24 volts is ok. It seems that the problem is mechanical alignment. Try this, remove the dryer rack from the machine and put it on top of a table where you can visually see all mechanical parts. Move the solenoid responsible for the paper that guides going up or down. While moving the solenoid manually, visually check the guide if it is moving perfectly, if not check from there what is the problem, probably it was not in its proper position. 

Probably not original but it doesn't matter now because the problem was solved by changing the laser module. $1K is much cheaper than refurbished laser unit. If this gun will going to lasts for 2 years then it is more than enough. The customer is making a lot of money for this machine. $1K of Gun every year is nothing. No need to argue if it is original or not because for sure it is not because it came from China. Thanks again for your useful information. I am learning so much from this forum. 

Please see the attached picture below if it’s original or not.

Optical noise inside laser unit. Probably in Blue channel having caused of this noise.

Original (maybe?) shimadzu purchased from Kanuo China 

I want to update you regarding this issue!  Replaced yesterday the Green laser head from Showa to Shimadzu with the original driver from Noritsu J391160 and Synchronous sensor error disappear. Printer is back to life. Once again thanks for the help. Till the next topic. 

43 minutes ago, yustas said:

If you would install now J391160 back with a Shimadzu HK9356 laser module- you would see a changed laser type.

Yes for sure. Based on your experience, which more reliable laser head between the two? SHOWA OR SHIMADZU 

1 hour ago, yustas said:

Hi,

You have H the first letter.

According to Noritsu guide it shows the G laser driver type: 

• H: G laser driver (J391231)

• I: G laser driver (J391160)

 

You have H.

So your laser unit now is B1.

H because the installed driver and the laser is J391231. but as I said again and again, the previous laser head and factory installed green laser is Shimadzu with J391160 driver and for sure the letter I will display in system version check.

3 minutes ago, davidlam said:

it depends on qss-owners altitude, some treat lases like "exposure lamp",,,, as cheap as possible as long as it works !!! 

Of course some are being scammed

What did you mean? 

Can Anyone tell me the image attached what type of laser unit is in my Qss 3701

Minilab service : I can't able to check those measurements at the moment because it needs to travel by plane.

Please anyone who has an original, brand new shimadzu green with driver please send me a quote. 

Do you recommend that it is better for me to install the shimadzu HK-9356-02 green than Showa? Shimadzu was installed from the factory when first time opened the laser unit, but because showa is cheaper, I choose Showa instead of Shimadzu. 

These are the Showa green laser. The first image is original and 2nd is made in China. 

Minilab service I think you are right. The J391231 that came with the green laser gun has no CN4 but the R54 is in the right place. This Pcb has also a sticker with Chinese characters. As I remember my customer purchase the laser gun with a driver less than $1000. 

Did any of you can analyse the values of diagnosis that I have attached? 

Can anyone analyze the values below when laser diagnostic performed of the printer  that had an error of synchronous sensor error? These values below has no error but maybe somebody can tell that these values of green will help to identify the real  problem of the green laser,

Minilab service: I don't knew if the Showa I installed is Made in China or not. As you have said, it might be not original because I really measured 7.3mV. I want to ask you if there is any chance of having faulty on laser control board? Because why when shutting down the printer for a couple of minutes and turning On again then the printer works perfectly. 

G laser head should work on laser driver pin 2 have 0 V , but on resistor have not voltage then something wrong with laser head, bad connection between them, or faulty laser driver.

If when laser works on laser driver pin 2 have not 0 V then laser control doesn't work properly.

Minilab service, can you elaborate further what did you mean about your quote aboved?