Jump to content

Tengi2

Members
  • Posts

    29
  • Joined

  • Last visited

About Tengi2

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Tengi2's Achievements

Advanced Member

Advanced Member (4/10)

0

Reputation

  1. I onced experience with this error when doing daily setup, the setup failed and the paper come out almost blank except last two lines. I swapped two ram between the pc and the image pcb, the error was cleared but unfortunately images failed to open when printing as the ram from image pcb were too small, I then replaced one ram from PC with another 256mb ram from my spare bank and the problem was solved
  2. Thank you all for your remarks, the idea of using fuji catridge chemical come as an alternative to regular chemicals used in noritsu qss 3001, these chemicals are becoming scarcy in my local area, it seems the dealers are focusing more on cartridge chemicals than standard RA-4 chemicals.
  3. Is it possible to use frontier chemicals sold as cartilage in noritsu? If yes how mixing is done, I know frontiers processor mix chemical automatically, but in noritsu we mix manually 2L of reprenisher in 8L of water for those chemicals from Lucky.
  4. Thank you all for your feedback, I am going to adjust the distance from the wall as suggested by Dave S and check the fans as davidlam and yustas said, a mini air conditioner is also on the way to be installed.
  5. Hi, I have experienced operational difficulties in my lab during hot days and hours, the lab displays errors such as 6073-003, 6073-002, and sometime 6073-001 (synchronous sensor error), swaped in vain the AOM drivers,and replaced the laser drivers with no lucky. When the lab is switch of for sometime to cool,it then work fine untill exausted again one of the error recurs, the machine is installed against two walls, one facing the back side and the other facing the left side of the machine, the room is very compact with small free space left. Can these condition cause any trouble to the lab? Or is it possible some errors reported to be caused by software issues, so a clean reinstallation of the system can solve the issue
  6. Tengi2

    FUJI PICTURE FRAMES

    Thank you very much sir, am going to keep my eyes wide open for the link.
  7. Tengi2

    FUJI PICTURE FRAMES

    Can you send to me those frames the way they are, never mind in which format they are. sudoapt2012@gmail.com
  8. Tengi2

    FUJI PICTURE FRAMES

    I know how to create frames in PS but it takes a lot of work to get similar products, that is why I am asking for already made frames.
  9. Hi, every one I need fuji frames for printing pictures, as I own noritsu minilab but my customers are not satisfied by noritsu frames, therefore, I am asking for any one who can send those fame via my email sudoapt2012@gmail.com Thank you
  10. Hi to all I recently changed paper type from fuji to lucky, and now I want to perform initial setup based on lucky paper but I am not sure which option to choose when prompted to choose the paper type, I used to select crystal archieve type one with fuji papers, when scrolling the list I only find LUCKY SA2, LUCKY SA5, LUCKY SA6, LUCKY SA10 AND LUCKY SA20, the list goes on But unrelated with lucky (to my opinion). The paper I bought is Lucky SA26. Which way to go now. Thanks
  11. Hi every one. I have faced the above error two times at an interval of one week, everytime I resolved by switching the machine off for 5 hours and than switched on, the error is gone, when it happen I swaped the AOM drivers, but the error code remains the same. Any help in solving this error permanently. Thanks
  12. Yes these are the ones, already got them on aliexpress
  13. These parts numbers worked like magic in AliExpress, all gears found in one supplier.Thank you Minilab Service.
  14. Thank you for your post AliExpress have them all, though if you don't know their names or part number it is difficult to find them, thank you very much "Minilab service" for the parts numbers, helped me directly in the huge AliExpress market.
  15. Hi every one, I still own the old 3001 minilab, and it is working fine right now but I suspect the three rear gears (I don't know how to call them) are in their last minutes, thus I suppose a backup of then in handy is the way to go. I have attached two pictures to show those gears labelled 1- 3, the first gear is attached to the same rod with the worm gears that drive racks, the second gear is in between the first and the third gears, while the third gear is a two line gear that is attached to the motor (I think it is synchronization motor). Any one with these gears please drop your contact for further arrangement. Thank for your time.
×
×
  • Create New...