Jump to content


  • Posts

  • Joined

  • Last visited

  • Days Won


pskaro last won the day on May 1 2017

pskaro had the most liked content!


About pskaro

  • Birthday 05/16/1969

Profile Information

  • Gender
  • Location

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

pskaro's Achievements


Maxi (9/10)



  1. Hola quiero saber si puede ayudarme con mi kis dks 1510..Calibro el papel de 20,3 o cualquiera y al imprimir una foto con fondo blanco.....sale cian el blanco....es la mascara??  la uniformidad el problema .Ya descarte un problema quimico no es Gracias saludos


    1. HORACIO


      Gracias !!!  ya lo corregi con la ganancia del lcd .saludos


    2. Junior


      Tienes que rehacer la polarización del filtro.

    3. HORACIO


      gracias junior

  2. Hola PsKaro Que modelos de escaner epson acepta el kis1510? gracias  saludos


  3. Dear pskaro,

    I would like to use an Imagus 1500 SCSI scanner, but I have noticed that the image is out of focus and the image quality is much lower compared to a PAKON F135 plus. I would like answers to a few questions.

    IMGAUS 1500
    The machine works with SCSI and XP, standalone.

    1. I have found that the film holder does not click into the scanner properly. It's like he's not in place. I tried to secure it with a strap. What could be the problem? Why don't you click into place?

    2. The images are unfortunately out of focus unfortunately. Not terribly, but enough.

    3. Very strongly compressed with ultra setting in addition to JPEG. It would be great to access the raw uncompressed file (TIFF).

    Thank you very much in advance for your advice!

    Happy New Year!

  4. Zdravo,

    Vidim da si iz Hrvatske i da znaš dosta o labosu. Razvijam filmove za sebe i komercijalno u ATL1000 procesoru, E6, C41 i CB. da bih svoje troškove smanjio. Međutim to već neko vreme prevazilazi moje mogućnosti. Neki prosek dnevno je 5 filmova za sada bez rekleme već me ljudi preporučuju. Mogu da nabavim V30, V50 ili V100. Kontam da je V30 najbolji izbor za malu količinu filmova. Do sada sam radio sa Kodak LORR LU hemijom, regenerišem blajh i fiksir a razvijač koristim one shot. Da li imaš neke smernice za razvijanje u mašini, koliko često da se mašina stavlja u pogon, kako se regeneriše i sl.

    Srdačan pozdrav i unapred hvala,

  5. Zar vam Milan inače ne servisira stroj ?
  6. By the way, I charged the customer only 50€ for that repair, probably too little, but it was easy to diagnose and fix, and I did not have to go on site, so...
  7. If the prints are coming wet from the dryer, then there is a problem with in a dryer. There are several items to check, most common is blown thermal fuse (there are two inside, replace both, less then 1€ each), bad motor capacitor and that is the most common reason for blowing of the thermal fuses as it starts later and heaters are already ON (it should be 1.5uF, but over time it's capacitance is going down, replace it, less then 3€). Then it could be the heaters itself, but they are wired separately, so if one is bad then the other should work, thermal probe (NTC resistor) or the bad contacts of that probe on the board or in the connector, and on the end, very rearly, the heater or blower SSR relays. Two days ago I repaired one same dryer (customer brought complete section blower+heater assembly to my work place), I found one blown thermal fuse (I replaced both, as the other one looked bad), and blower capacitor measured at 1uF and it should be 1.5uF, I replaced it with the same value, checked the heaters and thermal probe, and both were OK, and that was it
  8. That is the densitometar lamp, it should be ON only during during measuring the paper test
  9. In the ZIP file (beside 3 sharpness test iamges for DKS2, but it should be OK for DKS3) there are also 2 PDF files, one explain the procedure, and in the other one are markes for tracking changes while doing mechanical adjustment off the angles screws or changes in up/down position off the lens, to be printed on regular A4 paper. This is the download link: https://jumboiskon.tportal.hr/download/37755b7c-8531-442a-9514-c562679503f4
  10. By Monday I will post a link to download few test images which I made a long time ago to help you with sharpness procedure, together with some technical info about it and KIS reference marking tables for easier tracking off the screw and lens ring adjustments;)
  11. Time consuming process, but there is no other way, piezzo test would also help a little bit. Also, the lenses on DKS2 were better quality, Rodenstock, I think ?
  12. You need to do few tests, but for some (like Zero Adjustment, the top cover have to be open to mechanically adjust best sensor zero position) and some understanding what you are doing, maybe the best is to leave it for the technitian, but.. 1. Zero Adjustment Go to SU/Settings/Zero Captors + LED 2.Lens and LCD offsets adjustment: GO to tab SU/Settings//OPTICAL/OFFSETS/START 3. Optical centering: Go to SU\Centring\Lens 4.Centering setting: Go to SU/Centring (fine tune on the end, can be skipped if the top 3 solved the problem)
  13. You can also change the dryer temperature in TransportPapier.ini [CUVE] PasSeparOrdre=860 PasSeparPile=14 TailleMaxPile=1 AttenteNbTopDensito=285 ConsigneAirHaute=70.0 (+10C from standard, used after new dryer start after pause, for limited time period) ConsigneAirBasse=60.0 (standard working dryer temperature)
  14. Beside bing technician for minilabs, in the past I was assigned to monitor E6 process and I run control strip every day and plot the parameters, and correct the process with NaOH and dilute or make more concentrated baths if necessary together with checking the chemistry concentration measuring it for specific gravity, and along that I run C41 and RA4 control strips if needed for some minilab owners. But last time I did it was 10 years ago
  15. Only Adaptec SCSI controller will work, SCSI-2 is I think OK
  • Create New...