Jump to content

Nand Gw

  • Posts

  • Joined

  • Last visited

Everything posted by Nand Gw

  1. Nand Gw


    Crystal AOM Deflector
  2. Nand Gw

    Sp 3000

    if Press the scanner’s START switch then everything not start (Monitor ,PC Indicator not show) - Check line in OK. - Press hold the scanner’s START switch and Press the PC Toshiba Power button. if everything start OK but it error message E-4xxx show. - Check image processing box malfunctions. -ECC SD-Ram (512x2) -IEEE Card Good luck
  3. Re-Version printer to 6.6 for clear X2101. (Printer Ver.7.6 or 7.7 for FMPC)
  4. Nand Gw

    lines on print

    Check motor M561 and Belt flat
  5. Nand Gw

    lines on photo

    Replace CTL20 (Frontier 350)
  6. -S-alone Sacanner -install A1 (FR390) -select SE maintenance -select Update scanner standalone -select inherit data form FD
  7. Goto mainmenu and connect DI server (FRONTEND) in menu 1.Pre-Ope (I-1595)
  8. Replenisher Modify Guideline for all chemicals solution. this pics modify for Cpac RA-QT
  9. G-SHG Laser leak out be effective Magenta on white area ( light or dark color depend on leakage )
  10. Nand Gw

    Those Laser Heads?

    Problem of Laser 1. Dust on mirror optics surface inside laser unit because laser up light beam density R,G,B to gray scale. 2. Densitometer measurement " NG " cause laser up light beam density R,G,B to LUT and use the light beam density peak level (Max Power) all the time. 3. Chemical 4. Filter 5. Room temperature proper Cool < 23-25 > hot. Because laser warming up before beam
  11. - Paper Magazine Registration (0221) - Next page - "Correct value" box for correct value dryer temperture.
  12. - setup and maintennance - menu "1023 (custom button registration/saving)" - select "service" - press "initialize" button
  13. 1 - Run Calibration sensor - adjust value +/- in Pre-High speed box again. if if problem not clear 2 - adjust Belt tension (marking old position before loosen screw (yellow or white marking)
  14. If roller feed film condition OK Manu 44Q NC135Y Machine Data Setup Change value +/- in Pre-High speed box (std value = 995-998)
  15. set correct Date/time on scanner and FDi .
  16. Step A 1. download data from HD to Carrier (0447) and test feed film if problem not clear Step B 1. Run Calibration sensor (0440) 2. Run Sensor Calibration information (0442) and click EEPROM Writing 3. Open (0448) NC100AC Machicne Data setup and next to 3rd page 4. Click EEPORM reading 5. Change value in box " Corr of 135 frame to scanning (1000-1100) " + or - 5 number / time and click EEPORM wrinting and test feed film
  17. Nand Gw

    Frontier 340 Error

    SOS is detect R laser light beam but FR330/340 be no AOM driver therefore this error code 2529 SOS Detection might laser unit faulty.
  18. FR330/340 have 6 model MCU (FC2010, FC2011, FC5010, FC5011, FC7010 and FC7011) FC2010, FC2011, use in FR330 (first model) it use HDD 40 GB only and 4 partition set by recovery CD FC5010, FC5011 use in FR330/340 it use HDD 40 GB only and 4 partition set by recovery CD FC7010 and FC7011 use in FR330/340 it use HDD 80 GB only and 4 partition set by recovery CD use Recover CD not match MCU will be blue screen appear If change M/B use Intel M/B (945 chipset or lower) with support win2K SP4
  • Create New...