Jump to content

Alpek

Members
  • Posts

    44
  • Joined

  • Last visited

    Never

About Alpek

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Alpek's Achievements

Advanced Member

Advanced Member (4/10)

0

Reputation

  1. Hi everyone! Please help me to solve this problem on my Frontier 390. Having the following errors. I-2307: Laser temperature adjustment not completed in exposure section. Please Wait. and. E1131: Offset cancellation failed. Call technical representative Many thanks. Alpek
  2. Hi Eder and SERVMANMEX, and others. Your help is highly appreciated. Kindly guide me about this. I have checked in the software floppy and compact discs I received with the machines and found just bacup and older versions of software. I do not even know exactly which softwares are needed. What I am sure of having is the C4-C5 for FDI only. Kindly list for me which softwares with latest version so that I can look around for them. Best regards, Alpek
  3. HI SERVMANMEX. THANKS FOR THE ADVICE. DO YOU MEAN INSTALLING THE SOFTWARE ON THE SP2500 (FILM SCANER)? REGARDS, ALPEK
  4. Dear Eder, Many thanks for your help. Please help me to identify the board you are telling me about. The location in the machine and the part number if possible. Kindest regards, Alpek
  5. Hi Dear Minilabhelpers. Kindly help me to fix these 2 errors on my Frontier 390. They appear when loading the paper magazine. E2430: PAPER WIDTH GUIDE 2 IN EXPOSURE SECTION FEED UNIT MALFUNCTIONS. CONTACT TECHNICAL REPRESENTATIVE; and E2439: CALIBRTION OF THE HOLE SENSOR IN PRINTER FAILED, (THIS IS FOLLOWED BY NUMBERS 202222... ). My technician has failed to understand what are the cause for these errors. Please anyone with a clue help me. Many thanks to you all. ALPEK
  6. Alpek

    FRONTIER 370 LDD20

    HI! MY FRONTIER 370 NEEDS LDD20 PCB. THE PART NUMBER IS: 113C893919E. PLEASE ANYONE WITH INFO HELP ME TO SOURCE IT. THANKS VERY MUCH. ALPEK Alpektrader@yahoo.co.uk
  7. Hello everyone. Anyone breaking this machine (QSS2611)? I am looking for part number J30681805. (monitor card). I also need the floppy drive (T1601A) for the same machine. Please get in touch if you have them. Thank you very much. Alpek
  8. Hi Christina Rose, Sisir and others who contributed to this exchange. I finally found the fault, thanks to your contribution. The LDD20 PCB for my Frontier 370, P.No: 113C893919E is faulty. The machine is giving error :E2515 and when we replaced the LDD20 with an other one the error disappears. I was told it is possible to repair the LDD20 instead of buying a new one that costs in region of USD2k. Is there anyone who can advise me where to have it repaired? I keep watching here for your help. Thanks Alpek
  9. Alpek

    LDD20 PCB REPAIR

    Hello everyone! The LDD20 PCB for my Frontier 370, P.No: 113C893919E is faulty. The machine is giving error :E2515 and when we replaced the LDD20 with an other one the error disappears. I was told it is possible to repair the LDD20 instead of buying a new one. Is there anyone who can advise me where to have it repaired? Regards, ALPEK
  10. Hi! I am in need of theses if not highly priced. please send me an email to: Alpektrader@yahoo.co.uk Where are you based? Regaeds, Alpek
  11. Hi! For proper help, you need to tell the readers where you are communicating from. This may well be a problem due to your electricity supply (source). Pretty similar to my case. Bought a frontier F370 in UK and took it to Africa where most people think that these machines are like tv sets or dvd players where you just go and plug the power cable in the power outlet and press power button to play. My frontier was on 3 phase in UK but I had single phase in my high street shop. Wires had to be modified accordingly, but the technician did not take that into account. We worked on that fatal error for about two days while installing but then ... a blast. That was it and it was a very serious problem gone far into a very hidden and bank safe-looking box inside the machine, called power supply. It distributes power to all the components in the machine and that is where you will need to check. But you have to be a very qualified technician not a DIYer. An other issue depending on your location, power stablity in the machine. Not like in Europe where most things are done to precision, power in some countries is unstable, so the necessity to use a stabiliser to keep electricity constant. Otherwise you will repair many times. Let us know how you it goes. Alpek
  12. Thanks for your ideas. They are very much appreciated. I am going to do all the checkings and will report back the findings. Kind regards. Alpek
  13. Hi everyone. My Frontier 370 is recurrently bringing this message (R laser led temperature abnormal) and I am getting worried it could be the laser problem . Could anyone be knowing the reason for it please? Thank you for you help. Alpek
  14. I had the same problem, Tried all the possible solutions on this website but in vain. End result was a success!... I ended up by opening the F-DIA instruction manual and using my computing skills, did litterally what the manual says... Instaled the C4-C5 software and reconfigured the networking all alone.... guess what, I did it defeating all Fuji techs who had failed to see the cause. TRY THE SAME!...
  15. I had the same problem, Tried all the possible solutions on this website but in vain. End result was a success!... I ended up by opening the F-DIA instruction manual and using my computing skills, did litterally what the manual says... Instaled the C4-C5 software and reconfigured the networking all alone.... guess what, I did it defeating all Fuji techs who had failed to see the cause. TRY THE SAME!...
×
×
  • Create New...