Jump to content

Br iSmith

  • Posts

  • Joined

  • Last visited

About Br iSmith

Recent Profile Visitors

799 profile views

Br iSmith's Achievements


Member (3/10)



  1. Hey guys have a magazine set up for 8 inch that continuously pulls the paper to far into the magazine each time you rewind. Is there a manual adjustment for the magazine or is it a software adjustment ? Many Thanks
  2. Hi Guys running a 370 with pic 2.6 . I have 2 computers in the upstairs of my lab running Photoshop and Lightroom. There are times that it would be very convent to send a small job straight to printer without having to get up run downstairs and spool from PIC. Is there any way with software or Hot Folders that we can send images to print from computers up stairs. They are all networked together by the way. Many thanks
  3. Hey guys need to replace rubber covered bearings on guide plate in the exit of the exposure section of LP2000Sc on frontier 370. If there are any of you who have done it is there any tips to getting to it. Also if any of you are techs just out of curiosity what would the labor cost be if you did this repair in the field.
  4. I have attached a document that explanes how to start up from CP 48 xls. I do not know if the ratios will be the same for 48LR. Frontier 370 - 375 Startup from Concentrate.pdf
  5. Does anyone know if SPFE (Society of Photofinishing Engineers) is still around and if so contact info. It used to be trough PMA which is now The Imaging Alliance but am having no luck finding any information on it. Sabrina
  6. Neil I think that as long as we in the labs can keep the equipment under us and can continue to obtain good quality chemicals we can continue to offer this service for c-41 and e-6 as long as the manufactures continue to provide the film. Taking into mind that volume and utilization is a key.
  7. This attachment will help you with proper rep rates for your processor and paper type. I am not familiar with the 550. On the 370 it is in maintenance mode under processor adjustment. 600004889.pdf
  8. Hey guys I'm just curious here as to how many of you guys run control strips? I don't post much at all but I do occasionally scan the forums to see what's going on and it seems like there are often times when working tanks are being dumped as a (TEST) to see if it solves a particular problem, when in all actuality a simple control strip could rule out chemistry. I do understand that chemistry is far superior than it was back in the day and that equipment is tighter than ever before with regards to replenishment, circulation, ect. and that there is probably no need for a daily strip run but I always keep strips in the fridge of some unforeseen issue. How about you guys?
  9. Sounds like Sulfa from the bleach (P2). If it is clogging the filter every day then most likely the bottom of your working tank is full of it and will need to be drained and flushed. Could be several causes but most likely from low utilization or under replenishment.
  10. Br iSmith

    370 Shutdown

    Hi Guys I have a 370 that goes al the way thru shutdown process and then starts back up. It goes to the point that it should click off then restarts and never shuts down. It's like it it's in a loop. Also errors 1424 Download carrier failed and 1143 scanner not up. Have cut all power to both units many times to hope and reset but no luck. Would it have anything to do with floppy disk? If it needs to be replaced what is the process machine on of off? Many thanks. Sabrina
  11. Sherwood there is a Hot Folder option in a list under setup.exe but it is not bold in the list and I can NOT click on it. Any ideas as to how to access it.
  12. Hey Guys I am running a 370 with PIC 2.6. I am trying to find a way to send quick proof 4x6 or 5x3.5 to the printer from an upstairs PC rather than having to run down stairs and waiting on the PIC to load 125 ect images each and every time I finish an edit job in Lightroom. Is there a way to send these images from my network location to the PIC or frontier directly? I edit approxamitaly 10 shoots a day that need quick proofs and I would be easier to send print request from my desk rather than running up and down stairs all day. Frontier and PIC ARE viewable on my network. Any Thoughts?
  13. The typo that I was speaking of is in the subject line.
  14. hi I'm running a 370 and was wondering how often the floppy should be changed and is it as simple as just ejecting the old one and installing the new one or are there other steps involved?
  15. PIC 2.6 Just crashed with following error: Windows XP could not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM I fear that I may have to reinstall windows and PIC I have the following cd's can you tell me if I have everything that I need to reinstall and in what order to install. PIC Vr 2.6.1 Installation CD Fuji Personality PIC 2.6 CD PIC 2.6.1 service pk 3 cd PIC Lite 2.0
  • Create New...