Jump to content

Leaderboard

Popular Content

Showing content with the highest reputation since 04/16/2021 in Posts

  1. There is a software that I have wrote 15+ Years ago for use on digital carriers. It obsolete and ugly but plenty of people using is with printers even this days ... and it's totally free. Just remember - it start printing with windows default printer on current size settings without asking anything. You can create your own formats from menu file -> New format ... asks if any questions. https://mega.nz/file/ytd1xQDL#g-dVvrNtqQMI1jmW2Bj9lKeb3sjZ5TZN_7-aTyQL8m4
    2 points
  2. Minilab service

    QSS 3501 F

    Here is fast RA process. For this minilab you need replenishment cartridge. If going daily make many prints then can use cartridge, which you have ( CP-49LR - low replenishment rates ) . Just on processor settings need change replenishment rates. If going to print not very much - better to use CP-49HVII ( CP-49HV , CP-49E ) . Then replenishment rates will be higher. To fill tanks can buy CP-49 start up kits ( for developer and for bleach fix ) . For water need super conditioning tablets. All information : https://www.fujifilm.com/us/en/business/photofinishing/photographic-chemical
    1 point
  3. You can try this: https://www.pixel-tech.eu/drylab-system/#about I know people who use it with satisfaction. I prefer the good old FUJIFILM MS.
    1 point
  4. He asked for Windows XP, so there 32 bit. All software versions can work on Windows XP - from EZ controller version 1 to latest - version 7.20. Noritsu QSS3704 system software can also can be any. Are you sure, that want any version? System software version 11 and lower has bad white balance. Only since version 12 this problem was fixed. Oldest EZ controllers works bad, if compare with modern version. New versions can be installed on W10 64 bit, so do not see reason, why to use XP. The latest software for QSS3704 are : Ez controller version 7.20 QSS2704 system software vers
    1 point
  5. The upgrade can be performed before or after the MS01 installation. However, it is common practice to do the firmware upgrade first.
    1 point
  6. This cannot be removed. It does this so you can be sure the top of the printer is clear to eject the print. The long ejection unit is very fragile. A paper jam in that section will likely break something.
    1 point
  7. CREATE A PRINTER BACKUP BEFORE STARTING!!!! Start the 370 in ROM mode. Turn on the printer and instantly press [MENU] [<] [>] [ENTER] in that sequence. Place the MS01 CD into the FMPC/LPC computer. Navigate to (DC DRIVE)\EZ171\firmware tools\LP1500_LP2000 Run the 1500-2000 Firmware.bat file Then prepare the backup floppy and run the 1500-2000 Floppy.bet
    1 point
  8. Hello. DL-600 can't be converted into SL-D3000 DR. Can convert only DL650. SL-D3000 DR and DL650 are the same. Different only firmware, driver, system software and cartridges. DL600 is the same printer, but has one color less. From print head removed one element and has 5 cartridges. Color configuration is different, than on SL-D3000 and DL650. I-1303 means confirmation for intermittent printing. One long length sheet printed. To continue printing, you need to remove print from the tray. Remove the prints from the tray, and then click [OK]. The same message is on Epson SL-D
    1 point
  9. Minilab service

    V8 files

    First question is not correct. Probably nobody except me understand what you are talking about. Both software names you wrote not correct. If you really have similar software then not sure, that it work on MS. All questions you have ask your software supplier. If they gave software they should explain you everything.
    1 point
  10. davidlam

    noritsu 2211

    when monitor is supposed to be "ON", can you feel statics or hear statics ? I suspect problem could be the high tension (voltage) supply failure to the CRT . . . Just a wild guess
    1 point
  11. Minilab service

    noritsu 2211

    QSS2211 is old analog minilab. It has not computer. There connected small monitor with video input, where can see pre-scanned images. First check power suppliers. Maybe something missing there.
    1 point
  12. davidlam

    noritsu 2211

    Woo...QSS-2211. A general reply will be [ Try to connect an external monitor or display]. Do you feel machine is still working -or- 2211's pc is not starting up. Can you share a photo of your QSS-2211 for us to look at ?
    1 point
  13. Solved! Issue was indeed with the pressure roller solenoids. One of them was rock solid!! Thank you both. Cheers Dave, that diagram especially helped a lot.
    1 point
  14. Glad to hear it alive.
    1 point
  15. Things are getting confused here! I004074-00 is a solid state relay; the 5V input that you measured here will be coming from your PC via the USB cable. The power supply I038404-00 on the diagram (red X on your photo) should have your countries AC supply voltage on the input side and 5V DC on the output side. The other power supply I038405-00 on the diagram should have your countries AC supply voltage on the input side and 24V DC on the output side.
    1 point
  16. On your screenshot no added printers. From the same menu load MS01 backup, made when all worked. All should be restored and system should work well. If FMPC software installed new then on left box need select LP1500 and press Add. Then LP1500 will be added on right box. During instillation need choose correct configuration ( FMPC, or tethered printer ) and choose printer ( scanner ) model.
    1 point
  17. In most cases it cause heater. Disconnect heaters and compare resistance. If one of them has different resistance it will be faulty. All heaters are the same - 200V 200W/240V 288W. If resistance similar can be that heater has current leakage to ground. Try disconnect all heaters ( unplug heater connectors ) and turn on minilab. Of course chemicals will not heat, but you see your wall breaker will be disconnected, or not. If wall breaker will not be disconnected then one by one connect heaters and allow to preheat tank. Look, which heater disconnect wall breaker. If when connecte
    1 point
  18. Dave S

    E-2529

    Come on man, using this forum to direct people to your own website is not a very ethical thing to do. How would you feel if I came onto your forum and directed people here?
    1 point
  19. If I see well one relay is RY8 and other RY9. Look do you have P+24V voltage on connector PAC24 pin 2. Is it stable? Measure between this pin and ground ( PAC24 pin 3 ) . If have - check +24V after fuse CP3 ( voltage C +24V, it is on diode D5 cathode ) . This diode is beside relay RY9. Beside RY8 is diode D4. There to cathode P+24V connected directly.
    1 point
  20. Na ir ką čia dabar pasakoji? Nieko nesuprantu. Jei nori atsakymo - rašyk Angliškai.
    1 point
  21. yustas

    Fuji570 red gun

    They like to buy cheap crap in China and then find the answers here for free. Smart guys rule!
    1 point
  22. Minilab service

    Fuji570 red gun

    Which adjustment you are talking about : 1. Red laser head is original and was not removed. You want to make laser beam position adjustment 2. You installed new laser head and need adjust everything. In first case go into minilab maintenance menu. There make Main Scan/Laser Beam Sync. Rough Adjust and Laser Beam Sync. Fine Adjustment Print. In second case need adjust everything - laser power, current, make R laser head position mechanical adjustments, focus adjustments and make tests above. How to do all that have to ask your laser head supplier. When I repair laser head I explai
    1 point
  23. davidlam

    L1 installation

    L1 supplier can
    1 point
  24. Nieko nesuprantu. Rašyk Angliškai.
    1 point
  25. Ko klausi? Man atrodo viską pasakiau praėjusioje žinutėje.
    1 point
  26. Hello. Do not understand your language. This is international forum, so write in English. You should respect other forum members, if want to get answers to your questions
    1 point
  27. Are you kidding? If it was inside processor 15 minutes then processor was not running. You have do following : 1. Take piece of paper and keep it on the light. 2. Run processor 3. Through control strip gap put paper inside processor. processor will take it. 4. Leave processor running and wait paper. It should go out from dryer. 5. If paper blue - have replace chemicals and check all ( circulation, replenishment, temperatures and etc ) .
    1 point
  28. I also a bit confused now... Customers always mix two different things: AOM and AOMdriver. If you have defective AOM - see my message about it (above) If you have defective AOM driver- no need to open the laser at all. Just buy new one or search the way where to fix it.
    1 point
  29. wrong forum room, sorry
    0 points
  30. svp vous pouvez me torouver un bckup pour ordinateur client
    0 points
  31. Old version is here : https://files.fm/u/wgfyvn28 Can install it on Windows XP, need dongle to run, has not all features, which can see on latest version ( 6.8 ) .
    0 points
×
×
  • Create New...