Jump to content

FOTOBINCI

Members
  • Content Count

    16
  • Joined

  • Last visited

  • Days Won

    1

FOTOBINCI last won the day on July 22 2014

FOTOBINCI had the most liked content!

About FOTOBINCI

  • Rank
    Member

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. HOW MUCH IS THE UPDATE? HOW DO YOU INSTALL IT? I AM USING A PC WITH WINDOWS XP CAN I INSTALL EVERYTHING ON A PC WITH WINDOWS 7? CAN YOU HELP ME WITH THE INSTALLATION OF A GUIDE? THANKS FOR THE REPLY. STEFANO BINCI
  2. I answer to Minilab service, after cleaning the plate as Bakul advised me, I reset the paper and the densitometer for this the first is very green then after the usual three checks it was fixed, this morning I did as usual the daily check and everything went well, not like the first one that gave me the error (# 2003), I run the installation again) so I think he was right Bakul dirty calibration plate. Thanks anyway to all of you for advice and good work. Attached this morning check and some high quality prints.
  3. I cleaned the calibration plate, in fact it was dirty and yellowed, I redid the settings as per attached photos and it didn't give me more control (failed to set up correctly #2003) Thank you very much for your explanations, the next few days I will tell you if the problem has been solved
  4. Sorry, P1 ok we print an average of 800/1000 photos a day, how to clean densitometer (calibration plate?)
  5. P1 ok stampiamo una media di 800/1000 foto al giorno, come si pulisce densitometro (piastra di calibrazione?)
  6. CHE COSA CAMBIA TRA IL SOFTWARE NORITSU SECONDO LEI PIU' AGGIORNATO E QUELLO DI FUJI PIU' VECCHIO? cI SONO DEI MIGLIORAMENTI SULLE STAMPE O E' PIU' VELOCE? WHAT CHANGES BETWEEN THE NORITSU SOFTWARE AS YOU MORE UPDATED AND THAT OF FUJI MORE OLD? ARE THERE ANY IMPROVEMENTS ON PRINTS OR IS IT FASTER?
  7. fuji frontier lp7500 failed to set up correctly. (#2003) perform the setup again, doesn't densitometer work? it never gives me the ok, while if I check the paper it's fine.
  8. HELLO TO ALL, I HAVE A PROBLEM WITH MY FRONTIER 350 SOME DAYS I DO NOT PRINT MORE '20/30 PHOTOS, MI FROM ERROR W-2406 (2) AND REMAINS A SHEET OF PAPER UNDER THE DISTRIBUTION AND A SHEET OF EXIT FROM PAPER BOX, THE LAST PICTURE 2 LEAVING THE OVEN IS IN PART AND GLUED OVERLYING, I HAVE TRIED TO CLEAN THE SUCKERS DISTRIBUTION BUT NOTHING ANYONE CAN 'HELP ME? Insert THREE PHOTOS photo 1 on the monitor shows the message 3 photo paper has stopped before the rollers in question photo 5 under the distribution remains a sheet of paper THANK YOU
  9. Hi, I have a Frontier 350 the heater of the PS1 and PS2 will not turn off even when the thermostat says OFF and the temperature of the PS2 reaches 45 degrees, and the message heater turned off. Sometimes for days the error does not occur, sometimes as today I had to turn off and let cool chemistry PS2 three times. Can you tell me what's the problem?
  10. Thank you, in fact, the latch that holds the small bearing is blown, it was necessary to riassemblareb everything and put new firm, thanks to all problem solved,
  11. Digita il testo o l'indirizzo di un sito web oppure traduci un documento. Annulla Traduci da: italiano Hello, I have a problem with my Frontier 350 paper stops just before the rollers that push the rack P1, the two rollers that should move it forward until the rack P1 do not run, error-W .2406 ( paper jam between exposure and distribution section (6).(1) thanks so much
  12. Frontier 340, solution in the replenisher tank Remain I tried to drain the chemical mixing containers, I re-inserted a new cartridge in chemistry but I have always the same error, the pumps are working well. Can anyone help me? thanks
  13. No way, I tried to install the driver downloaded from the site, when I turn the printer tells me "USB device not recognized" and when finally installed during the print test tells me "unable to print the document" In Italy the original driver can not be found yet, and I unfortunately I need it now. Thanks anyway. Stefano
  14. I tried with the driver, OKI 710, but does not work, I have requested the software to Kodak representative told me that should come out but that still is not available. But there? Does anyone use it? If so, where can I find? I have two Kiosco Kogak G3 and GS and the printer Kodak DL2100 well as invitations to print calendars and so on, should I also use the catalogs to brochures and more. Thanks anyway
  15. Hello, I want to print with Kodak printer DL 2100 duplex from my computer (Windows XP) but I can not find the drivers, can you help? Thanks
×
×
  • Create New...