Jump to content

Search the Community

Showing results for tags 'standalone'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Site News
    • Site News - CLICK TO VIEW
  • General Area
    • Digital - CLICK to enter our Digital discussion boards
    • General Chit Chat forum Section CLICK TO VIEW
    • Non Photographic
    • Other Areas
  • Mini-Lab Equipment
    • Noritsu Help and Support
    • Fuji
    • Kiosks
    • Wide Format Printers forum CLICK TO VIEW
    • Kodak
    • PhotoMe/Kiss
    • Agfa
    • Fotolusio Forum Section - CLICK To View
    • Doli
    • Marko Line / Gretag
    • Konica
  • Kodak Express
    • KEX Public Forum
    • KEX Private Area

Product Groups

There are no results to display.


Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 5 results

  1. Thanks in advance for being patient with a new member who's just getting started in an area of photography for which I have very limited previous experience. I'm working with someone right now who has a Fuji SP2500 scanner that was previously configured and working for standalone operation. It's networked to a Windows 10 HP laptop running PIC 2.6 and something called FES in a Windows XP virtual machine under VMWare. All of this was working fine until mid-November, at which point it inexplicably stopped. I've been trying to help them get it back up and running, but don't have expertise on the equipment. I have a lot of experience with computers and electronics in general, and am old enough to have used NT4 and XP when they were new. When the scanning computer starts up, I get this message: I-595 Connect to Imaging Controller for updating data. When I click [OK], I get this error: W-1531 F-DI device registration failed. Check the network connections. Press {Retry] to retry or [Cancel] to cancel. Retrying doesn't help. If I cancel, I can get the scanner to go through what seems to be a series of calibration steps with a film carrier in place. I've checked the network cables and connectivity. Both machines can see shared drives on each other and move files back and forth. They each have a DHCP assigned IP address, and canned be pinged from each other successfully and consistently. Both are assigned to the same Windows Workgroup (MICSGROUP). For the life of me I can't figure out what might have changed to make it all stop working. My colleague doesn't have any disks, and the person who set this up originally is no longer available. I was able to find a folder with what looks like installers for PIC 2.60.0034 and Fuji Personality Disk 2.6. The scanner is attached to a Toshiba 5600FF computer. My colleague also has another one of these scanners that was never configured for operation, but that uses a Toshiba G10 computer. I fired that one up long enough to make sure the computer works (it does). I swapped the computers between the two machines to see if it would help, and it didn't. That machine is available as a source of spare parts. I have some old PC's that run Windows XP natively that I could configure for this project if that would help. I don't see how running PIC in a VM would make this fail when it previously worked, but I'm willing to try anything. If anyone has or can give me detailed instructions for diagnosing and repairing this problem or starting from scratch, I'd be very thankful. If there's someone or someplace I can get the correct software to make this happen, I'd be very glad to know that too. I've had poor luck finding enough information to get this going, and I'm hopeful this group's knowledge and experience will get me on the right path. I'm glad go back and get more information off the machines if that helps. Any advice would be gratefully received.
  2. Hello Recently I got Konica R2 Film Scanner with usb-key. Also I got Phenix software version 2.00 which I installed on Windows 2000 SP4. I planned to use it as standalone scanner for personal film scanning at home, but this is not so easy as I thought before. The hardware of my PC is next: GIGABYTE GA-6VEM \ PENTIUM III Tualatin \ PCI 1394 card. When I run Phenix, I get error with code L1778 (The Input station to control the Printer processor is not found) How can I fix this problem?
  3. Hi, I have a Frontier 370 V 7.7 connected to MS01 V 4.2 via scanner. O would like to know about hardware and software for stand alone function. Thanks.
  4. Hi guys, New to this forum and am finding it very hard to find much information on precise steps to get this done. Basically, I am helping a friend set up a Frontier SP 3000 to be used as a standalone unit. The machine/software on the scanner is fine, but we are missing the steps and software to get the secondary computer set up to have the files exported to. I understand this computer needs to run Windows XP which we have installed. Is there anything else other than needing the software installed and it obviously networked via ethernet? Unfortunately my friend said the secondary computer that came with it died and the seller is not communicating back so we've bought an old one as a replacement. We just wanna get this thing going and get scanning! Any information on installation files would be greatly appreciated. Thank you for reading, Patrick
  5. I am looking to get a Noritsu scanner, but I am curious if the S2 or S3 models can run standalone, or if it needs to be connected to a printer to operate.
×
×
  • Create New...